Extenders

HDMI Extender over Single Cat5e / Cat6, 1080P - 60 Meter (197ft)

FireFold's HDMI Extender lets you extend HDMI audio/video signal by up to 60 meters (196 feet) over single Cat5e/Cat6 Cable. The HDMI Extender kit includes both the local transmitter and remote receiver units, perfect for point-to-point digital signage applications that require high quality HDMI™ video. For perfect performance, the extender comes with a EDID function on the transmitter, which enables user to adjust the signal to best match the cable length.

Vanco 280501 HDMI® Extender over Single Cat5e/6 Cable with IR

The Vanco 280501 HDMI Extender over Single Cat5e/6 with IR, extends high definition video and audio signals, and IR, at a distance of up to 196ft/60m over a single Cat5e/6 cable. No EQ adjustments are necessary as the receiving unit automatically adjusts for gain by just a push of a button. Fully supports 1080p high definition resolution, multiple audio formats, and is HDCP compliant. In addition, IR pass-through allows for source control with IR accessories included. With Power over Cable or PoC functionality, only 1 power supply connected to the transmitter is needed to power up both the transmitter and receiver. For extending HDMI over a single Cat5e/6 at a long distance, with IR, the 280501 is a great cost effective solution for any application!

Tech Support Tips:

• Recommended to be used with a permanent source, or non-rotating source. For any rotating source such as a conference room type setup, it is recommended to use an HDBaseT extender
  
• HDMI UHD Deep Color mode on some LG displays may need to be deactivated to avoid video signal issues
  
• Input Signal Plus on some Samsung displays may need to be deactivated to avoid video signal issues

Quest offers a HDMI Extender that allows you extend HDMI

The HDMI™ Extender lets you extend HDMI™ audio/video signal by up to 60 meters (196 feet) over single CAT6 cable. The extender kit includes both the local transmitter and remote receiver units, perfect for point‐to‐point digital signage applications that require
high quality HDMI™ video. It also works to extend Infrared IR signals from remote controls, ideal for controlling your video source from your video destination. For perfect performance, the extender comes with a reset function on the receiver, which enables user to adjust the signal to best match the cable length.

PulseAudio ARC Digital Audio Extender

The PulseAudio PAEXARC1 is an ARC Digital Audio Extender that allows digital audio to be routed from a display, back to a remote location or amplifier, over a single Cat5e/6 cable up to 492ft (150m). For displays without ARC capability, or when ARC settings are not working as they should, the built-in “ARC Backup Plan” is featured where audio can still be extended utilizing SPDIF. For applications where ARC signals need to be extended above HDMI® cabling limitations to an amplifier or distributed audio system, the PAEXARC1 is the perfect solution.

The range of the PAXEARC1 will vary depending on the HDMI®/ARC sample rates. For instance, higher sample rates, 192kHz, will be rated at 295ft (90m), while lower sample rates, 96kHz, will be rated at 492ft (150m).

USB 1.1 Extender over Ethernet up to 150ft

Note:: Ethernet patch cable sold separately.

The maximum distance for a USB cable is typically 15 feet. After that, the USB signal begins to fade and reliability becomes an issue. USB cables with repeaters are one solution, but the USB-EXTENDER can carry your signal far beyond the scope of a booster. They use the twisted pairs of a single Ethernet cable to achieve extraordinary distances. Using this extender set, you can increase your distance to up to 150 feet using Cat5E cables. It is compatible with Windows and iOS platforms, so it can be used with most PC and Mac computers. No software installation is required.

Rated for USB 1.0 and 1.1 standards and specifications, the USB-EXTENDER is best suited for printers, keyboards, and mice but may not be appropriate for external hard drives, cameras, or charging and syncing mobile devices. It is also not recommended for use with wireless devices such as USB WiFi adapters. These extenders are small and require no power source, so they can be easily stashed anywhere. The single Ethernet cable is also easily run through conduit for a simple in-wall solution.

j5create Wireless Display HDMI Extender

The JVAW53 HDMI^™ over Wireless Extender includes a transmitter and receiver kit. It can send a high definition video and audio signal to an HDMI^™ enabled TV set, projector or LCD PC monitor display device with receiver distance up to 60 meters and nearly zero latency.

Users can extend other HDMI^™ sources, including DVD players, Blu-ray^™ players, PCs, notebooks and gaming machines (ex. Sony^® PS4^®, Nintendo Switch^™). The JVAW53 is fully HDCP compliant via HDMI^™, supporting resolutions up to 1080p and stereo digital audio. The extender also supports the transfer of IR remote control signals to the receiver side.

Basic product functions and application scenarios: converts the passage of the HDMI^™ or IR signal into a wireless signal, converting it into a flexible means of transmission and reception. It addresses the issue of the TV being too far away from the host by eliminating the need for wires, allowing the TV to be moved outdoors for long distance use.

During meetings, projectors or large touch screens mounted high above can also be used to create a wireless conference room and/or a wireless media environment.

Broadcast Wirelessly. No Wi-Fi® needed.

Simply connect an HDMI™-enabled source and transmit audio and video wirelessly

Optimized Viewing Experience

Watch your favorite videos in HD anywhere you like without costly cable installation and clutter.

Ultra-Low Latency with a Broad Wireless Range

Extend HDMI™ audio/video signals up to 200ft. (60m) with nearly zero delays (less than 0.06s/60ms).

Vanco 280703 Super IR HDMI® IR Adapter ADAPTER HDMI IR PATENTED

USB 2.0 Cat5e/Cat6 Extender Via Single RJ45 Ethernet

This USB extender allows you to conquer 150Ft USB length limitation, Connect your USB peripherals and important equipment without regard for proximity. The USB Extender uses Cat5, Cat5e, or Cat6 RJ/45 cable to extend the range of your USB devices by up to 150Ft feet. The units compact design allows for easy placement behind equipment or around corners. Its simple: One side of the USB Extender attaches to your USB peripheral, the other to the USB port on your PC. The three aforementioned cable options connect them in the middle. Gone are the days of trying to fit all your peripherals onto one desk. The USB Extender simplest way to spread your equipment out.

Techlogix Networx Fiber-based SFP to SFP Media Converter

TechLogix media converters adapt fiber signals to a variety of different formats and/or cable types.

The TL-MC-1S1S features two SFP ports (SFP module sold separately), effectively adapting signals between different fiber types. In most applications, the TL-MC-1S1S adapts single mode fiber to multimode fiber and vice versa.

The MC-1S1S supports multimode fiber when paired with a multimode SFP module and single mode fiber when paired with a single mode SFP module.

Quest HDMI Repeater, 35M, 4K X 2K

Quest offers a HDMI Repeaters that boost the A/V signals via HDMI cable up to 35 meters (115ft) at 4K2K@30Hz.

HDMI Extender 4K 70m

The Evolution by Vanco EVEX4K70 HDMI Extender over single Cat6 with Digital Audio Breakout, HDMI Loop-out, IR, and PoE, extends 4K@60Hz, 4:4:4 Chroma, and HDR10 up to 230ft/70m. Vanco’s patented bi-directional Power over Ethernet (PoE) Technology transmits power over Cat6, allowing either the Transmitter or Receiver to be powered without the use of a power supply for an easy installation. The transmitter is equipped with an HDMI loop-out for local monitoring or use with other distribution products. The receiver features digital optical output to break multi-channel audio out to amplifiers for a better listening experience. No EDID or EQ adjustments are necessary as the units automatically adjust for compatibility and gain. In addition, bi-directional IR pass-through allows for source and/or display control. For extending full 4K resolution with up to 60Hz, 4:4:4 chroma subsampling, and HDR10, with options for connecting additional displays and breaking out audio, the EVEX4K70 is a great plug and play solution for connecting the latest components!

The EVEX4K70 includes two units: transmitting unit (EVEX4K70-TX) and receiving unit (EVEX4K70-RX). The transmitting unit is used to capture the HDMI input with IR signals and carries the signals over a single Cat6 cable. The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR signals.

*NOTE – All specifications and ratings for the EVEX4K70 have been tested and confirmed using Cat6 cabling. Cat6 or better is strongly recommended for optimum performance, achieve rated distance, and to maximize resolution capabilities of this product. Cat5e is not recommended and may not achieve distance and/or resolution expectations.

The MC200CM is a media converter designed to convert 1000BASE-SX fiber to 1000Base-T copper media or vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-SX standards, the MC200CM is designed for use with multi-mode fiber cable utilizing the SC-Type connector. The MC200CM supports shortwave (SX) laser specification at a full wire speed forwarding rate. It works at 850nm on both transmitting and receiving data.

Techlogix Networx TL-CPT-HD01 HDMI 

Tired of cables scattered across your conference room table? How about untangling knots when all you want to do is connect your laptop? Meet the TL-CPT-HD01.

This compact device provides a clean, low-profile connection point for tables, podiums, desks, racks and credenzas. Simply mount it to the underside of a flat surface and connect one end to your destination device using an HDMI cable. Your classroom or meeting room is now ready for plug-and-play connectivity.

The PureLink AV HCE II Tx 4K HDMI over HDBaseT Transmitter is designed for in-wall cable installations. It allows you to extend HDMI signals past the typical 50 foot maximum using Ethernet cable. Cat6A or Cat7 Cables are recommended for maximum performance.

The HCE II supports embedded lossless audio formats, bi-directional IR signals, and HDCP-protected content. The ultra slim design makes for a compact, discreet installation.

Extend your composite RCA signal by up to 1000ft with this balun.

It transmits the signal using CAT5 or CAT6 Ethernet cable to another balun, and eliminates the need for long composite cables.

Evolution 4K HDMI Extender over Single Coax Cable with Bi-directional IR

The Evolution by Vanco EV4K2004 HDMI Extender can send and receive 4K resolutions over single RG6 coaxial cable with Bidirectional IR. Capable of extending 4K@60Hz up to a distance of up to 330ft/100m and 4K@60Hz with HDR10 High Dynamic Range up to 230ft/70m. The EV4K2004 also features bi-directional IR, which allows for control of the source or display. Also features dynamic EDID management, which allows and encourages source and display “handshake” for seamless integration. Compact design with mounting ears included, for an easy and flexible installation. Can’t run a Cat6 cable to a location? No problem, the EV4K2006 is a great solution for applications which already have an existing RG6 coaxial cable in place.

The EV4K2004 includes two units: transmitting unit (EV4K2004-TX) and receiving unit (EV4K2004-RX). The transmitting unit is used to capture the HDMI input with IR signals and carries the signals via one RG6 coaxial cable. The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR and control signals. The EV4K2004 offers the most convenient solution for HDMI extension over a single coaxial cable with long distance capability, and provides a solution in applications where additional cables cannot be installed.

*Installation Note: RG6 coaxial cable must be used, RG59 and mini coax will not work with this product; coaxial connections must be BNC and home-run cable strongly recommended.

The PureLink AV HCE II Rx 4K HDMI over HDBaseT Receiver is designed for in-wall cable installations. It allows you to extend HDMI signals past the typical 50-foot maximum using Ethernet cable. Cat6A or Cat7 Cables are recommended for maximum performance.

The HCE II supports embedded lossless audio formats, bi-directional IR signals, and HDCP-protected content. The ultra slim design makes for a compact, discreet installation.

Techlogix Networx Fiber-based Media Converter - 1 SFP & 1 RJ45

TechLogix media converters adapt fiber signals to a variety of different formats and/or cable types.

The TL-MC-1S1R features one SFP port (SFP module sold separately) and one RJ45 twisted pair port, effectively adapting twisted pair-based devices to fiber for longer transmission distances. The MC-1S1R supports multimode fiber when paired with a multimode SFP module and single mode fiber when paired with a single mode SFP module.

Two TL-MC-1S1R media converters are required for most applications -- one for each end of the cable run.

HDMI® Extender over Fiber with KVM USB Pass-through

The Evolution by Vanco EVEXFBRK1 HDMI Extender with KVM, bi-directional IR, and RS-232, extends 4K HDR video and audio signals up to 984ft/300M over multi-mode fiber optic cables, and 6.2mi/10km over single mode fiber optic cables and modules! USB 2.0 KVM allows for controlling a security NVR/DVR, computer, NAS system, or any other component that is controlled by USB with this extender. No need to run a separate line or extender just for KVM control! Bi-directional IR pass-through allows for source and/or display control. Also features RS-232 pass-through for additional control. For extending HDMI with 4K HDR resolution at an extreme distance, the EVEXFBRK1 is a great solution for any application.

The EVEXFBRK1 includes two units: transmitting unit (EVEXFBRK1-TX) and receiving unit (EVEXFBRK1-RX). The transmitting unit is used to capture the HDMI input with control signals and carries the signals via fiber optic cables. The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR signals. Both units require power.

The BG-USB-LR100 USB 2.0 Extender over Single Cat.X allows USB devices to be extended at distances up to 100 meters (328 feet). This unit consists of two devices - transmitter and receiver.
The transmitter is located at the computer while the receiver connects to peripheral devices such as printers, cameras, storage devices, and more. The receiver features a 2-port USB hub to allow connection for multiple devices. When you need a reliable, long-range solution for USB 2.0 connectivity look no further!

The BG-EXH-70C 4K HDMI extender can transmit an uncompressed 4K@60Hz HDMI signal with zero latency at distances up to 70 meters. By utilizing a Cat6/6A/7 network cable this extender allows a signal to be transmitted farther than is possible using standard HDMI cables. Digital audio extraction for an external audio system can be done via the S/PDIF port and supports LPCM, DTS-HD, DTS-Audio, Dolby Digital, and Dolby TrueHD audio formats. The HDMI loop-out allows for an additional display on the transmitter side. Plug and play setup, bi-directional IR pass-through, and surge protection ensure easy setup, flexibility, and reliability.

ADAPTER IR SENDER 1.5M

<!-- features -->

• IR Transmitters- Receivers- and Adapters are compatible with Vanco’s HDMI Matrixes- Splitters- Switchers- and Extenders that are enabled with Super IR technology
• HDMI IR Adapter Allows for IR Control over any Vanco HDMI Cable
• Extends IR Signals more than 100m/328ft
• Supports Dual Band IR
• HDMI IR Adapter is IR or CEC Configurable

Using HDBaseT technology, the ZIG-HVX-70R from ZIGEN extends an HDMI signal up to 70 meters using a single Ethernet cable. It also transmits bidirectional control signals for ultimate convenience. It can be used as a stand alone solution or combined with matrix switch setups to extend the input or output cable distance.

This HDMI extender supports resolutions up to 1080p and 4Kx2K Ultra HD. It supports simultaneous transmission of RS-232 and IR signals from a control system, enabling remote control of source devices or displays.

Tired of being restricted by HDMI distance limitations in complex setups? Say goodbye to that frustration with the VIP-100 II HDMI over IP distribution system from PureLink AV. This transmitter can be combined with a compatible receiver to transmit over distances up to 364 feet, or 120 meters.

Get audio/video, RS-232 and IR extension coupled with matrix switching capability up to a 64x190 system to meet the needs of even the most complex and demanding setup. Point-to-many and many-to-point are also supported.

USB 2.0 Extender over Cat5e/6 Cable

The Evolution by Vanco EVEXUSB2 is a full function USB 2.0 extender over a single Cat5e/6 cable, information and control can be transmitted up to 330ft/100m over Cat5e and 492ft/150m over Cat6. Supports up to four USB 2.0 devices such as webcams, microphones, touchscreens, printers, cameras, scanners, USB flash drives, keyboards, mice, etc., and supports gigabit switch cascade capabilities. Perfect solution for security monitoring, gaming, industrial control, professional audio-visual, smart medical and more.

Intellinet Outdoor Gigabit High-Power PoE+ Extender Repeater

IEEE 802.3at/af Power over Ethernet (PoE+/PoE), Extends Range up to 100 m (328 ft.), Metal, IP65

Extend the range of a PoE connection — even in harsh outdoor conditions.

The Intellinet Network Solutions Outdoor Gigabit High-Power PoE+ Extender Repeater (561211) is designed to extend connection distances from a PoE source to an output device up to 100 m (328 ft.) via Cat5e or Cat6 cable. Cover even longer distances by cascading up to five extenders. The PoE+ Extender Repeater does not need an additional power supply, as it draws the power it needs from the PoE input.

Designed for Outdoor Use

With an IP65 rating and a vast operating temperature range of -40 – 75°C (-40 – 167°F), the Intellinet Network Solutions Outdoor Gigabit High-Power Power over Ethernet Extender Repeater can be deployed in harsh conditions, which sets it apart from its indoor counterpart, the Intellinet Network Solutions PoE+ Extender (560962).

Simple Installation

Simply connect the "PoE In" port with your PoE injector or PoE switch and connect the "PoE Out" with the PoE device that you wish to connect (e.g., a VoIP phone or a PoE network camera). That's it. There is nothing to configure. It simply could not be any easier.

Reduced Wiring Costs

No need to run AC power lines for your wireless access point, network camera or IP phone. Simply connect the PoE Extender to the LAN switch port and use the existing Cat5 cabling to deliver DC power as well as transfer data.

Power over Ethernet 802.3at Compliant

The Intellinet Network Solutions Outdoor Gigabit High-Power PoE+ Extender Repeater supports the IEEE 802.3at protocol. It is designed to forward data at Gigabit speeds and provide up to 25 watts of input power to a connected IEEE 802.3af- or IEEE 802.3at-compliant device. The cable length on both ends can be up to 100 meters (328 ft.), bringing the total distance to 200 m (656 ft.).

Cascading Power

Daisy-chaining multiple PoE extenders increase the transmission distance even farther. Be advised that each added PoE extender draws up to 4 W of usable PD power, and additional power losses will occur as the cable length increases.

18-GBPS HDMI Extender with Bi-Directional Power

The POC-100 is an innovative new product from Zigen supporting 4K/60Hz 4:4:4 HDMI 2.0, Bi-Directional IR, and RS232 extension over single UTP/STP cable. If the application does not need ARC support, but requires robustness and cost effectiveness, then the POC-100 is deal for all your residential HDMI distribution.

The ZIG-POC-100 is designed to be powered from either the Tx or Rx side. Ideal when cascading multiple extenders for longer reach or when powering from a particular side is not ideal.

HDMI 4K Extender over Single Cat6 w/ IR Extension - 229ft

When trying to extend a HDMI connection, using longer HDMI cables may not be an option, nor may it be easy to run the cable in the walls of your residential or commercial building when compared to Ethernet cables. The HDMI extender over Cat6 cable provides an efficient and simple method to extend the HDMI connection using Ethernet cables. With support for resolutions up to 4K 60Hz at 229 feet, expanding the HDMI signal couldn't be easier, while supporting Ultra HD resolutions for an optimal viewing experience.

How it Works

The HDMI extender comes with a sender and receiver. The sender will plug into a HDMI source, such as a Blu-ray or DVR player. On the other end of the sender is a Cat6 RJ45 Ethernet port. A Cat6 cable is plugged into the RJ45 Ethernet port and then plugged into the other end on the receiver side. On the receiver side, another HDMI cable would then plug into a display for output. IR cables are also included for using a remote control.

Metal Enclosure

Constructed with a metal enclosure, the HDMI extender provides a solid and sturdy build that can be used in a variety of applications.

4K 60Hz HDR Support

The HDMI extender supports resolutions up to 4K / 60Hz at 229 feet with Cat6/6a, delivering stunning picture quality at a longer distance. For those limited by 1080p over longer distances, this solves the issue.

IR Support

What's the point in extending a HDMI signal if you can't control the source device remotely. The extender includes IR support, allowing IR cables to be plugged in on the sender and receiver side. This provides remote control functionality on the display side.

HDMI Loopout, S/PDIF Audio Output, Lightning, Surge, and ESD protection

The HDMI extender features an HDMI loop out port for connecting and viewing a local HDMI display. The extender also includes a independent S/PDIF audio port for extracting and outputting audio. Easily switch between the two audio output modes on the receiver, ARC or S/PDIF. Audio Return Channel (ARC): Allows user to have one connection between TV to audio receiver or sound bar. Send video to the TV with an HDMI cable and the same HDMI cable sends audio from TV back down the same cable. Lightning, Surge, and ESD protection are all built into the device to keep it safe and lasting long.

Wall Mountable Design

Included with the HDMI extender are mounting brackets and screws. This extender features a wall-mountable design for a clean and flexible installation.

Applications

Evolution HDMI over IP Transmitter/Receiver

The Evolution by Vanco EVOIPLITE HDMI over IP Transmitter/Receiver is a complete audio, video, and control product over ethernet system. As a whole, the system has the ability to send multiple sources to multiple displays along with IR and RS232 pass-through, analog and digital audio breakout in TX mode, video up to 1080P@60Hz, with POE up to 100m when connected to a POE enabled switch off of a single Cat6 cable. This one single unit can be set to transmit or receive signals. When connected to a network with internet, the EVO-IP Cloud allows for additional features such as scheduling events or maintenance, remote monitoring of a system including remote diagnostics and troubleshooting, as well as voice control capabilities with Alexa! With an IP-less installation option as well as any new sources/displays being discovered automatically within the system, the EVO-IP HDMI over IP system is the fast, easy, and cost effective solution for both residential and commercial installations.

The BG-EXH-150C is a cost-effective and reliable solution for long-range HDMI extension. It extends HDMI audio/video signals, RS-232, and bi-directional IR at distances up to 150 meters (490 feet) using a single category cable. It supports resolutions up to 4K2K@60Hz. One HDMI loop port is available for signal passthrough at the transmitter end. It also supports audio de-embedding via the 3.5mm connection on the receiver. Two-way IR pass-through allows for both source and display control. The slim design of the individual components allows them to easily be integrated to existing systems.

Vanco 280544 VGA over Cat5e/Cat6 Extender with Audio (500ft)

Vanco’s VGA over Cat5e/Cat6 Extenders with Audio allow VGA and audio signals to be transmitted using a single Cat5e or Cat6 cable up to 500 ft (280544) or 1000 ft (280546). For control and fine tuning, the 280546 offers EQ and GAIN controls on the receiver balun to fully adjust for distance range and transmission signal optimization. The 280546 also features dual output, which allows for one display with audio at origin location and an additional display device with audio in a remote location. The 280544 and 280546 support computer resolutions UXGA (1600x1200), SXGA (1280x1024), XGA (1024x768), SVGA (800x600) and VGA (640x480)

HDBaseT HDMI® Extender 150M

Send 4K/60, HDR HDMI signals and bi-directional US type IR signals up to 120 meters (394 feet) and 1080p up to 150 meters (492 feet). Includes RS232 pass though for easy control signal distribution. Using the latest in proprietary DSC technology we are now able to offer an even better image quality than ever before giving trained eyes a run for their money to discern the difference between native or not video.

j5create JVAW56 ScreenCast HDMI™ Wireless Display

The JVAW56 HDMI™ Wireless Display supports multiple wireless standards including Miracast™, AirPlay® and Google™ Chromecast™. Users can extend their video sources by casting onto a bigger screen with an incredibly simple setup. The wide-ranging compatibility includes Windows®, Android™, macOS® and iOS®.

The JVAW56 supports signal speeds up to 802.11ac, providing a more stable wireless connection with resolutions up to 1080p. Its compact design with a built-in antenna can easily fit in your pocket, making it perfect for home use and travel.

Turn Your TV into a Smart TV

Wirelessly display content from your mobile devices onto a high-definition TV. No apps needed!

Works with Various Cast-Compatible Devices

With its support of multiple wireless display standards (Miracast™, AirPlay®, and Chromecast™), the ScreenCast is compatible with devices and TVs you already own, including Windows®, macOS®, iOS®, Android™ and cast compatible laptops, tablets and mobile phones.

 Native support for AirPlay®, Miracast® & Chromecast™ (Google Cast™)

Wirelessly display content from your compatible device without connecting the ScreenCast to the Internet.

Quick and Easy Setup

1.  Quick and Easy Setup
2. Plug the USB™ into the built-in USB™ port on your TV or a USB™ power adapter (USB™ extension cable included.)
3. Connect to the ScreenCast and share

The Wireless HDMI™ Extender lets you extend HDMI audio/video signal up to 100 meters (328 feet) via 5GHz band, with very low latency. The Wireless HDMI Extender includes both the Transmitter and Receiver, ideal for the point to point digital signal extension situations that require high quality HDMI™ video and some place which have the limitation to physical wire connection. It supports up to 4 displays to show one source content synchronously and resolutions up to 1080p. It also allows user to control source device from display side via source device’s remote controller.

NOTE: This product is intended to be used in an open area (same room). Signal strength is not guaranteed through walls.

Techlogix Networx TL-IR-CC IR Coupling cable 

How many times have you had to output an IR signal from your control system to the input of an HDMI extender? In the CI world, this is an extremely common requirement. For years, the solution has been to tape the IR emitter from the control system to the IR receiver of the extender. Sometimes, the IR receiver is designed to rest on a surface and features a rounded, aesthetically pleasing appearance, but this makes attaching the IR emitter with a flat base difficult. Then, you have a wad of tape in the middle of two thin wires that turn that expensive installation into an unsightly mess. This is where the TL-IR-CC comes in.

The TechLogix TL-IR-CC allows direct IR to IR connections between devices. The IR IN (TRS) connector is compatible with an IR input which provides +5V DC to the tip of the connector. The TL-IR-CC allows a direct connection between the IR output of a third-party control system and a Techlogix extender. The TL-IR-CC will also allow daisy-chaining IR signals between Techlogix extenders.

Digital-Analog Audio Extender

The PulseAudio PA-EXTDA is a digital-analog audio extender over a single Cat5e/6. It is designed to extend the analog audio signals up to 170m, or digital audio signal up to 290m via toslink or coax audio input. Selecting the audio source is quick and easy with the use of a toggle switch. The toslink, coax, and RCA audio outputs are all synchronized and can be used simultaneously to provide digital and analog audio to 3 different audio devices at the same time without any lag between audio formats. With POC technology, the transmitter can be powered by the receiver for a for quick and easy installation.

The PureLink DCE II Tx/Rx DVI over CATx Extension System enables lossless DVI video transmission up to 220 feet using a single category cable. The active receiver uses the source device's power, so no external power source is required. This kit includes both the transmitter and receiver for a complete solution. Just add cables!

Wireless Extender for USB™ Cameras / Microphones / Speakers

The j5create Wireless Extender for USB™ Cameras / Microphones / Speakers turn your wired USB™ camera into a wireless one. With a wireless transmission range of up to 82 ft. (25m) users can extend the range of their wired USB™ camera without having to deal with tangled cables regardless of the room layout. In addition to transmitting both video and audio wirelessly this compact and lightweight camera extender works with Windows®, macOS®, and Chrome OS™ devices, making it a great addition to any meeting room, streaming setup, and other similar environments.

System Requirements:

• Available USB-C® or USB™ Type-A port
• Windows® 11 / 10
• macOS® 10.10 or later
• Chrome OS™

Special Notes:

• Display may vary depending on environment. Solid and nonporous materials such as steel, concrete, brick and glass (varies depending on coating and thickness) may cause shorter viewing distance or loss of signal.
• Priority of Audio-Output on the ports of TX would be “3.5mm Speaker→ USB™ Speaker/microphone → USB™ camera with speaker/microphone”
• TX and RX devices will connect and pair each other automatically. If devices are properly be paired and USB™ camera has been connect with TX, then camera will be activated automatically

4K Wireless HDMI Extender with HDMI Loop-Out

ScreenCast USB-C® Wireless Display HDMI™ Extender

Eliminate the need and expense for cables by wirelessly sending what’s on your laptop, tablet, or mobile phone to your HDTV with this HDMI™ Extender. It transmits audio and video signal from a USB-C® equipped device to an HDMI™ enabled TV, projector, or monitor, creating a dedicated AV connection without an existing network. Enjoy a large screen experience by simply connecting the USB-C® transmitter to your compatible device and then connect the HDMI™ receiver to your TV.

System Requirements:

• Available USB-C® port that supports DisplayPort™ Alt Mode

HDMI Extender Over Cat5e/6 Cable with IR and HDMI Loop-Out

The HDEX60 by Vanco extends 1080p high-definition video, audio, IR, and power up to 196ft (60m). Power over Ethernet (PoE) technology transmits power over Cat5e/6 cabling to either the transmitter or receiver unit without the need for a power supply. No EDID or EQ changes are necessary as the units automatically adjusts with dynamic EDID management. HDMI loop-out is built into the transmitter for connecting additional local displays, AVR, or other system components. IR pass-through also allows for source control from the display location.

Wall Plate Mixing Microphone and Analog Audio Extender

The PulseAudio PA-WPMIX Microphone Mixing Extender with dual-gang wall-plate transmitter extends and mixes balanced XLR and unbalanced analog audio signals up to 300m/984ft over a single Cat5e/6 cable. Mixing is done with an easy to use dial on the transmitting wall plate unit that is able to mix audio between the XLR and stereo AUX inputs. The PA-WPMIX also utilizes PoC (power over cable) technology so that the transmitter can be powered from the receiver with a single power supply allowing for flexibility. Have more than 2 sources needing to be mixed? No problem as an additional PA-TXMIX (sold separately) can be used and cascaded over a single Cat5e/6 for even larger solutions!

The PA-WPMIX includes two units: transmitting unit (PA-TXMIX-WP) and receiving unit (PA-RXMIX). The transmitting unit is used to capture the audio input(s) and carries the signals over a single Cat5e/6 cable. The receiving unit is responsible for converting the audio signals over the Cat5e/6 cable to a balanced XLR and 3.5mm stereo audio outputs.

Intellinet Industrial Gigabit PoE++ Extender

One 80 W Port, Extends PoE up to 100 m (328 ft.), IEEE 802.3bt (4PPoE) Compliant, IP30-rated Metal Housing, DIN-rail Mount

PoE++ Extender - double the range of your Gigabit Power over Ethernet connection, even in harsh industrial conditions

The Intellinet Network Solutions Industrial Gigabit PoE++ Extender adds up to 100 m (328 ft.) to the connection distance from a PoE source to one output device via Cat5e or Cat6 cable. This PoE++ (4PPoE) extender does not need an additional power supply since it draws its power from the PoE input.

Designed for harsh industry environments

This Power over Ethernet extender was designed to give you the network connections you need in places that are less than calm or temperate. With its rugged, IP30-rated metal housing, it operates reliably and quietly, even under extreme temperatures that range from -40 to 75°C (-40 to 167°F). In combination with its DIN-rail mounting option, it is ideal for IoT applications in Industry 4.0 and more.

Reduced Wiring Costs

This PoE++ Extender helps avoid the expense of running AC power lines for a wireless access point, network camera, IP phone, or other compatible device. Simply connect the PoE Extender to the LAN switch port through existing Cat5e/6/6a cables to deliver power as well as transfer data.

Power over Ethernet 802.3bt Compliant

The 4PPoE Extender supports the IEEE 802.3bt protocol over four pairs (4PPoE), which allows for a power input of 90 W. It forwards data at Gigabit speeds and offers up to 80 watts to a connected, IEEE 802.3bt-, IEEE 802.3at- or IEEE 802.3af-compliant device. The cable length on both ends can be up to 100 m (328 ft.), bringing the total distance between PoE source and device to 200 m (656 ft.).

Simple Installation

This PoE Extender was designed to be as easy as possible to set up and use. All it takes to have it up and running is to connect its PoE In port to your PoE injector or PoE switch and to connect the PoE Out ports to the PoE devices you want to connect (e.g., a VoIP phone and a PoE network camera).

Intellinet 2-Port Outdoor Vandalproof Gigabit PoE++ Extender

Two 30 W Ports, Extends PoE up to 100 m (328 ft.), 60 W Power Budget, IEEE 802.3bt (4PPoE) Compliant, IP67 Waterproof, IK10-rated, Metal Housing

This PoE++ Extender doubles the range of two Gigabit Power over Ethernet connections — even in harsh outdoor conditions

The Intellinet Network Solutions 2-Port Outdoor Vandalproof Gigabit Ultra PoE Extender adds up to 100 m (328 ft.) to the connection distance from a PoE source to one or two output devices via Cat5e or Cat6 cable. This PoE++ (4PPoE) extender does not need an additional power supply since it draws its power from the PoE input.

Designed for Outdoor Use

This PoE++ extender is the right power and data connector for its suitability to a wide variety of environments. Its weatherproof IP67 (waterproof and dustproof) rating, vast operating temperature range of -20 – 60°C (-4 – 140°F) and vandal-proof IK10 score make the Intellinet Network Solutions 2-Port Outdoor Vandalproof Gigabit Ultra PoE Extender able to withstand harsh conditions.

Reduced Wring Costs

This Ultra PoE Extender helps avoid the expense of running AC power lines for a wireless access point, network camera, IP phone, or other compatible device. Simply connect the PoE Extender to the LAN switch port through existing Cat5e/6/6a cables to deliver DC power as well as transfer data.

Power over Ethernet 802.3bt Compliant

This Ultra PoE Extender supports the IEEE 802.3bt protocol over four pairs (4PPoE), which allows for a power input of 95 W. It forwards data at Gigabit speeds and offers up to 30 watts per port to a connected IEEE 802.3at- or IEEE 802.3af-compliant device. The cable length on both ends can be up to 100 meters (328 ft.), bringing the total distance between PoE source and device to 200 m (656 ft.).

Simple Installation

This PoE Extender was designed to be as easy as possible to set up and use. All it takes to have it up and running is to connect its PoE In port to your PoE injector or PoE switch and to connect the PoE Out ports to the PoE devices you want to connect (e.g., a VoIP phone and a PoE network camera).