Klein Tools 85191 Conduit-Fitting and Reaming Screwdriver
The Klein Tools 85191 Conduit-Fitting and Reaming Screwdriver reams and smoothes 1/2" (13 mm), 3/4" (19 mm), and 1" (25 mm) thin-wall conduit ends. This protects wires and allows fittings to be installed more effectively.
The unique thicker hooded blade design keeps the tip of the screwdriver from slipping out of the screws during use, even when tightening hard-to-reach fittings. A longer cushion-grip handle provides comfort and additional torque.
The screwdriver reams both the inside and outside of the conduit at the same time. The reaming blade can be replaced and is held in place with a 1/16" hex socket set screw.
Klein Tools 56999 Conduit Locknut Wrench
Hard-to-reach cut-in boxes are no longer a challenge with the Klein Tools 56999 Conduit Locknut Wrench. This cleverly designed wrench allows you to easily reach 1/2 inch and 3/4 inch connectors in deep or tight boxes which might otherwise be impossible. The direct-heads rotate each other when twisted, so you can twist from one end and attach from the other. A screwdriver leverage hole in the head provides added torque.
An integrated wire feed hole makes this wrench ideal for situations where the box is already filled with existing wires, such as remodeling.
This innovative tool is manufactured with heavy duty steel construction and a rugged 9-inch grip. It carries the Klein Tools lifetime warranty, guaranteeing years of reliable on-the-job use.
Gardner Bender Hanger Strap, 10 Ft. X 3/4 In. Wide X 20 Gauge, GHS-1510
Gardner Bender hanger strap is designed for hanging and fastening conduit, pipe, or cables to joists, studs or other framing structures. This strap is galvanized to protect against rust and corrosion. It is flexible for good fits around pipe or bundles. Pre-punched holes throughout the strap allow for easy mounting.
Gardner Bender Plastic Conduit Strap, Secures Elect Conduit, Sched 40 PVC, and Copper Tubing, Grey
Securely fasten Schedule 40 PVC, copper tubing, and other electrical and plumbing cables and pipes with these heavy-duty polyethylene straps. Unlike metal straps these plastic straps won't rust and they offer stability against UV rays and extreme cold while withstanding deterioration and breakage. Easily installed with a hammer or drill.
From $3.39 - $4.77
Morris 3/4" Conduit Pulling Tape, 3000ft
Conduit Pulling Tape 3/4" - Tough Coated Polyester Conduit Pulling Tape is Used to Measure and Pull into a Conduit Run.
Conduit Measuring Tape 3/4" features include:
- Saves money on small cable pulling applications
- Thread, Measure and Pull with Single Product
- Imprinted with sequential footage markings
- Low Stretch Woven Polyester
- Fewer installation steps, significant material and labor savings
- Waterproof - Will not Rot or Mildew
- Tensile Strength: 2500 Lbs
- Length: 3000 Ft
- Order Qty of 1 = 1 Piece
Morris Conduit Measuring Tape, 3000ft
Conduit Measuring Tape - Tough Polyester Conduit Measuring Tape is Used to Measure the Length of a Conduit Run.
Conduit Measuring Tape features include:
- Provides Quick and Accurate Measurement of Conduit Runs
- 1/4" Coated Polyester
- Easy to read Markings in Sequential One-foot Increments
- Tensile Strength: 210 lbs
- Waterproof - Will Not Rot or Mildew
- Tensile Strength: 160 Lb
- Length: 3000 Ft
- Order Qty of 1 = 1 Spool