Low Voltage Brackets and Box Eliminators
Arlington Adjustable Depth Mounting Bracket, Single Gang
Arlington’s LVA1 is a single gang low voltage bracket with an adjustable depth to accommodate a wall width up to 1.5 inches. These non-metallic brackets are lightweight, sturdy, and versatile. Used primarily for new construction, they are ideal for installations in which the final wall thickness may not be known or when changes to the wall finish may be made in the future. They mount directly to both wood and metal studs and include side tabs for extra in-wall stabilization.
Adjustments can be made to the LVA1’s depth before or after the final wall finish is complete. The adjustment screw is flush with the bracket but readily accessed by simply removing the wall plate, allowing for changes at any time. Changes can be made with any Phillips head screwdriver. These Class 2 low voltage brackets are compatible with any standard single gang wall plate and will arrive to you pre-set at a typical half-inch depth.
Arlington Low Voltage Mounting Bracket for New Construction
Mount your wall plates vertically or horizontally with Arlington’s LVH1. These non-metallic brackets are ideal for any Class 2 low voltage cable run including AV and networking applications. Designed for new construction, they attach easily to any standard wood or metal stud. With three mounting hole options, these brackets can be oriented in nearly any position with a minimum of adjustment and no increase in installation time. Sturdy side tabs also help stabilize the bracket against the stud, allowing for a secure assembly.
The LVH1 is compatible with any single gang low voltage wall plate including bulk pass-through, keystone, and even decora-style faceplates. They include a molded tie-off slot for your pre-wiring cabling runs. This bracket is for use with low voltage wiring only and is not compatible with electrical runs.
Arlington LVA2 Adjustable Depth Mounting Bracket, Dual Gang
Arlington’s LVA2 is a two-gang low voltage bracket with an adjustable depth to accommodate a wall width up to 1.5 inches. These non-metallic brackets are lightweight, sturdy, and versatile. Used primarily for new construction, they are ideal for installations in which the final wall thickness may not be known or when changes to the wall finish may be made in the future. They mount directly to both wood and metal studs and include side tabs for extra in-wall stabilization.
Adjustments can be made to the LVA2’s depth before or after the final wall finish is complete. The adjustment screw is flush with the bracket but readily accessed by simply removing the wall plate, allowing for changes at any time. Changes can be made with any Phillips head screwdriver. These Class 2 low voltage brackets are compatible with any standard dual gang wall plate and will arrive to you pre-set at a typical half-inch depth.
Arlington Nail On Low Voltage Mounting Bracket for New Construction
Install your low voltage cables in a fraction of the time with the Arlington LVN Nail-On Mounting Bracket. The non-metallic, non-conductive, plastic construction makes them perfect for Class 2 networking and audio-video cabling runs. Designed for bare wood studs in new construction areas, these brackets come with a pair of angled captive nails and arrive to you ready to install. Simply tap the nails into the side of the exposed stud and you’re done.
They include a molded loop for tying off wires and a side tab for added stability. The unique side-fastening nail-in process also increases accuracy by decreasing pushback. The LVN low voltage mounting bracket is for use with standard wall plates and face plates. These nail-in style boxes are also available in two, three, and four-gang configurations. They are UL listed and CSA rated for low voltage use and are not compatible with electrical wiring.
From $0.99 - $4.79
Arlington Power and Low Voltage Box for Existing Construction
Streamline and simplify your retrofit project with Arlington’s LVDR2. This box allows you to combine one electrical and one low-voltage run into a single location, creating a clean look without any extra work. Designed for use with pre-existing construction, this combo bracket uses flip-up wings to stay fixed against the drywall. The tightening screw is easily accessible from the front of the bracket and the wings can adjust to accommodate drywall, paneling, and other materials up to 1.5” in thickness.
The power side of the LVDR2 includes a connector for Romex or other non-metallic electrical cables. On the low voltage side there are also knock-outs for conduit and raceway cable management covers- one ½” and one ¾”. These UL-listed combination boxes come in a standard two-gang size and can fit a variety of split power and low voltage wall plates for installation convenience.
DataComm Mid-Size Rough-In Bracket
Rough-in brackets are used in new construction as a means to run wires before drywall is put up. This greatly simplifies and speeds up the pre-wiring process and is an essential supply for any professional contractor or installer. DataComm’s 45-0101 is a mid-sized rough-in bracket designed for use with standard 16” on center wood or metal studs. The galvanized steel brackets are perfectly suited for use with a variety of DataComm’s mid-size low voltage plates including eight potential knockout locations for running conduit or armored cable. It also comes complete with a 2 ¾” steel electrical outlet box.
You can secure these rough-in brackets with the receptacle on the top or the bottom for the most flexible residential or commercial application. The thin but sturdy design is great for use behind appliances and televisions, including the low-profile TV mounts that can often otherwise pose a challenge to the installer. The 45-0101 rough-in bracket does not include screws for attaching the bracket to the studs, but it does feature a built-in mud ring for ease of use after drywall has been put up. This product is made for licensed installation professionals only. For a larger footprint, we also have full-size rough-in brackets available.INSTALLATION INSTRUCTIONS
Garvin Low Voltage Device Box Eliminator Ring
Help Eliminate Gangs
Limited wall room but need a wall plate? This product will eliminate the large gang box, allowing you to insert into any wall.
With the elimination of a standard gang box, you will be able to work with a deal more room. The blue (gang) box also makes cable management a hassle as thick, inflexible wire won't want to go back in properly. This leads to awkward angles that cause wear and tear and even a distortion in signal. Not all walls can support a regular gang box, and if you need an outlet in that particular place then you are essentially out of luck--unless of course you have one of these.
Single Gang Junction Box
Not all walls are created equal, especially when it comes to installation projects. Sometimes location, building code, or materials prevent running wires in the wall. Brick and cement walls are especially challenging, but that doesn’t mean you’re out of options. With a surface mount box like the SINGLE-GANG, you can create a way to attach wall plates without having to cut into your wall. Any low voltage wall plate will work: keystone, speaker, decora, HDMI. Just attach the wall plate to this single gang box like you would any other low voltage bracket using the two machine-threaded screw casings.
The SINGLE-GANG is designed for surface use and is not meant to be recessed fully into the wall. It offers several points of access for running your cables to it and through it. There are two rectangular knock-outs for use with Raceway cable cover systems and a 1.25” opening for conduit. To affix this single gang box to a wall, floor, or other surface, there are several holes to accommodate screws, nails, or other hardware. The smooth plastic is not porous enough to accept latex-based paints, but this single gang surface mount box is also available in beige.