Networking

Ideal for the more advanced networking installations, FireFold's Cat6 Bulk Cable is a must-have for any extensive networking application where a higher bandwidth is called for.

Category 6:

The next step up from standard Cat5E cable, Category 6 (Cat6) is a "twisted pair" network cable used for carrying data signals at speeds of up to 550MHz of Bandwidth. This cable is preferred for more advanced networking installations where a higher bandwidth than normal is required.

PVC Jacket

Our Cat6 Solid Bulk Cable comes wrapped in a sturdy PVC (Polyvinyl Chloride) Jacket, built to withstand high levels of stress, pulling, and pushing.

Solid Cable Design

Designed for more straight-forward, simple installtions, this particular style of Solid cable is perfect for most installations where cable runs do not require several bends and twists in the line.

Pull-Through Design

Since bulk cable is generally used in intervals, the box that it comes in is almost as important as the cable itself. This is the reason why our boxes are reinforced to provide excellent protection and are made with a simple pull-through design to keep your bulk cable free of kinks and knots while being pulled from the box.

The Cat6 jack provided by us comes with a standard RJ45 plug on the outside. While on the inside, wiring slots are in place for a tool required termination. All of our networking keystone jacks have 568A and 568B color codes on the jacks in addition to the easy trouble free 110 style termination.

Meeting All Requirements

Each RJ45 keystone jack is flame retardant and each is UL verified for quality and safety. These RJ45 jacks are 14.5mm wide by 16mm high and are easily able to fit in most standard keystone jack wall plates. Plus, they come in a variety of colors - both to help you keep your cables organized but to also allow you to match your keystone easily to whatever colors you are planning.

You can find a variety of keystone wallplates with us, which allow you to easily customize what you put into each wall plate in your home. You could combine one of these with a coax keystone, or even an RJ11 keystone, with just an easy snapping of each keystone into their place.

Please note: Slight hue variations may occur between keystone jacks and the matching keystone wall plates. If you need to ensure there is no variation, please contact customer service at 704-979-7100 before placing your order.

Vertical Cable Cat6 90 Degree Keystone Jack 25 Pack

The Cat5e Keystone Jack

The Cat5 Jack is the most widely used keystone jack in today’s market for networking wall plate solutions or patch panels. Each Cat5 Jack provided by FireFold provides outstanding performance, exceeding the TIA/EIA 568-B industry standard. This makes these keystone jacks perfect for use in today’s high-speed networks while remaining completely backward compatible with all previous standards.

The Cat5 jack provided by us comes with a standard RJ45 plug on the outside. While on the inside, wiring slots are in place for a tool required termination. All of our networking keystone jacks have 568A and 568B color codes on the jacks in addition to the easy trouble free 110 style termination.

Meeting All Requirements

Each RJ45 keystone jack is flame retardant and each is UL verified for quality and safety. These RJ45 jacks are 14.5mm wide by 16mm high and are easily able to fit in most standard keystone jack wall plates. Plus, they come in a variety of colors - both to help you keep your cables organized but to also allow you to match your keystone easily to whatever colors you are planning.

You can find a variety of keystone wallplates with us, which allow you to easily customize what you put into each wall plate in your home. You could combine one of these with a coax keystone, or even a RJ11 keystone, with just an easy snapping of each keystone into their place.

Please note: Slight hue variations may occur between keystone jacks and the matching keystone wall plates. If you need to ensure there is no variation, please contact customer service at 704-979-7100 before placing your order.

Our Cat6 Patch Panel is designed to provide amazing performance and cable management. Each Cat6 Patch Panel comes with 110-type termination while meeting and exceeding TIA/EIA-568B.2/568B.2-1 Cat.6 ISO/IEC 11801 hardware specifications.

These patch panels accommodate top, bottom or side cable entry. This leaves plenty of options on being able to get to your cables once you have everything set up. These IT patch panels are also able to handle wire diameters of 22AWG to 26AWG, so you should be able to easily find a wire to fit.

Each patch bay is a high-density 19-inch panel.

The Vertical Cable 043-382/24/1U 24 Port Blank Patch Panel comes with an add-on cable manager to provide that organized, professional look. It is constructed of high impact, fire retardant, heavy gauge steel with a powder coat finish for added durability. The universal mounting style allows for either left or right hinging and easy access to the panel.

Thanks to the fact that so much of our personal and professional lives now revolve around the Internet, to say that the quality of the networks that we depend on every day is important is a little bit of an understatement. Regardless of the size of the network you're constructing or even the environment that you're working in, anything less than the best just won't do in terms of your Cat6 Ethernet cable selections. For the jobs that matter most, FireFold is proud to lead the charge and offer some of the finest options available in that regard that money can buy.

With a performance of up to a stunning 550 MHz, our Cat6 Patch cable selections guarantee the speed, the versatility and the ingenuity you need when you need them the most. All of these cables feature not only an enhanced electrical performance (designed to support all of today's bandwidth-heavy applications), but they're also backwards compatible with any 10BaseT or 100BaseT network cards and hubs that you may currently be using.

All of these cables are constructed from four superior quality unshielded twisted pairs of 24 AWG stranded copper, complete with a sophisticated and rugged PVC jacket. The UTP wires themselves go a long way towards reducing the types of cross-talk that you're likely to experience in certain situations, all while helping to boost signal quality and data transmission at the exact same time. Even the RJ45 connectors have exceptional 50 micron gold plated contacts that are intended to help resist corrosion and degradation for years to come.

Not only that, but the molded strain relief boots present in our Cat6 Ethernet cable options help to avoid snags, tears and other issues during installation or maintenance that could potentially damage your cable over time. Make no mistake: these are molded in a very particular way not only to guarantee the flexibility you demand, but to also resist everyday wear and tear in a way that allows these cables to stand the test of time for years to come.

All Cat6 Ethernet cable options from FireFold come complete with a 60 day money back guarantee, a lifetime warranty and much, much more.

Networking Made Simple

Our Cat5E Patch Panel is designed to provide amazing performance and cable management. Each Cat5E Patch Panel comes with 110-type termination while meeting and exceeding EIA/TIA TSB-40 Cat5E connecting hardware specifications.

What makes it so simple?

Besides the 110 termination that this network patch panel offers, there are 12 individual Cat5E ports on the front side. Once you get your cables terminated on the one side, you just plug and go on the other. This is a very quick and easy solution for being able to swap out devices at any time. Plus, with numbered ports, you can easily keep track of what is plugged in where for better organization.

Need to mount this up where you won’t be able to reach it so easily? These patch panels accommodate top, bottom or side cable entry. This leaves plenty of options on being able to get to your cables once you have everything set up. These IT patch panels are also able to handle wire diameters of 22AWG to 26AWG, so you should be able to easily find wires to fit.

What makes these so great?

Each patch bay is a high-density 1.75 inch by 19-inch panel. This product is 1U, with a U (unit) being the standard size for a single rack interval. While others are 2 and 3U, there will be no such waste of space here.

These network panels meet TIA/EIA-568B.2/568B.2-1 Cat.5E ISO/IEC 11801 and EN 50173-1 specifications, so they are up to the latest standards. UL certified, they have been also tested to the highest standard for safety.

Vertical Cable Cat5E 90 Degree Keystone Jack 25 Pack

The Cat6 Keystone Jack

The Cat6 Jack is the most widely used keystone jack in today’s market for networking wall plate solutions or patch panels. Each Cat6 Jack provided by FireFold provides outstanding performance, exceeding the ANSI/TIA/EIA-568-B.2 industry standard. This makes these keystone jacks perfect for use in today’s high-speed networks while remaining completely backward compatible with all previous standards.

The Cat6 jack provided by us comes with a standard RJ45 plug on the outside. These ethernet jacks are toolless. The unique toolless design does not require the use of a punch down tool. This can make things substantially faster when having to put many of these RJ45 jacks into place. All of our networking keystone jacks have 568A and 568B color codes on the jacks in addition to the easy trouble free termination.

Meeting All Requirements

Each RJ45 keystone jack is flame retardant and each is UL verified for quality and safety. These RJ45 jacks are 14.5mm wide by 16mm high and are easily able to fit in most standard keystone jack wall plates. Plus, they come in a variety of colors - both to help you keep your cables organized but to also allow you to match your keystone easily to whatever colors you are planning.

You can find a variety of keystone wallplates with us, which allow you to easily customize what you put into each wall plate in your home. You could combine one of these with an HDMI keystone, or even an RJ11 keystone, with just an easy snapping of each keystone into their place.

Please note: Slight hue variations may occur between keystone jacks and the matching keystone wall plates. If you need to ensure there is no variation, please contact customer service at 704-979-7100 before placing your order.

This Cat5E STP (Shielded Twisted Pair) cable is perfect for an indoor networking application in a noisy environment. This rating of cable contains a shielding designed to resist crosstalk and electromagnetic interference that comes with networking in close proximity to other cable sources.

Category 5E

Considered the Industry Standard for most network installations, Category 5E (Cat5E) is a "twisted pair" network cable used for carrying data signals at speeds of up to 350MHz of Bandwidth.

CMR-Rated PVC Jacket

Our Cat5E Solid Shielded Bulk Cable comes wrapped in a sturdy CMR-rated PVC (Polyvinyl Chloride) Jacket, built to withstand high levels of stress, pulling, and pushing.

Solid Cable Design

Designed for more straight-forward, simple installations, this particular style of Solid cable is perfect for most installations where cable runs do not require several bends and twists in the line.

24AWG Solid Bare Copper Conductors

For this particular cable, the gauge is 24 AWG, which is a diameter of about 0.0201 Inches, or 0.511mm. 24AWG is the Industry Standard for any typical network cable installation. American Wire Gauge (AWG) is the standardized gauging system for measuring wire sizes.

Pull-Through Design

Since bulk cable is generally used in intervals, the box that it comes in is almost as important as the cable itself. This is the reason why our boxes are reinforced to provide excellent protection and are made with a simple pull-through design to keep your bulk cable free of kinks and knots while being pulled from the box.

Thanks to the fact that so much of our personal and professional lives now revolve around the Internet, to say that the quality of the networks that we depend on every day is important is a little bit of an understatement. Regardless of the size of the network you're constructing or even the environment that you're working in, anything less than the best just won't do in terms of your Cat6 Ethernet cable selections. For the jobs that matter most, FireFold is proud to lead the charge and offer some of the finest options available in that regard that money can buy.

With a performance of up to a stunning 550 MHz, our Cat6 Patch cable selections guarantee the speed, the versatility and the ingenuity you need when you need them the most. All of these cables feature not only an enhanced electrical performance (designed to support all of today's bandwidth-heavy applications), but they're also backwards compatible with any 10BaseT or 100BaseT network cards and hubs that you may currently be using.

All of these cables are constructed from four superior quality unshielded twisted pairs of 24 AWG stranded copper, complete with a sophisticated and rugged PVC jacket. The UTP wires themselves go a long way towards reducing the types of cross-talk that you're likely to experience in certain situations, all while helping to boost signal quality and data transmission at the exact same time. Even the RJ45 connectors have exceptional 50 micron gold plated contacts that are intended to help resist corrosion and degradation for years to come.

Not only that, but the molded strain relief boots present in our Cat6 Ethernet cable options help to avoid snags, tears and other issues during installation or maintenance that could potentially damage your cable over time. Make no mistake: these are molded in a very particular way not only to guarantee the flexibility you demand, but to also resist everyday wear and tear in a way that allows these cables to stand the test of time for years to come.

All Cat6 Ethernet cable options from FireFold come complete with a 60 day money back guarantee, a lifetime warranty and much, much more.

Printing Made Easy

There have been many ways to get your printer hooked up to your computer over the years. For example, parallel port (LPT) was used back in the late 1990s. It was a large, bulky adapter end that could easily just stop working properly if any of its many pins got bent or broken. It was inconvenient and annoying.

Well, nowadays, it’s far less stressing to attach your printer to your computer. Modern day printers typically use a USB printer cable. USB printer cables have two different ends on them - one square that goes into your printer and the other flat to go into your computer. Our USB printer cables here at FireFold are top notch! We provide them in a variety of colors and lengths to ensure that we can meet your needs.

Some Specifics

Our printer cords are rated for USB 2.0 which allows for hi-speed transfers of up to 480 Mbps. This is 40 times faster than the previous standard, USB 1.1. These cables are still backwards compatible and can even be used in most USB 3.0 ports. So, you should be able to find somewhere on your computer to tether your printer up with little effort on your part.

Each USB a to USB b cable is a thick 28 AWG, ensuring plenty of durability. This specific cable is thirty feet in length with a repeater to help extend the strength of the signal across the long distance it needs to travel. It does this repeating without any external power attached, allowing you to have just one cable for the lengthy run. The printer cords are each individually packed for extra protection when shipped or picked up from our offices here in Concord, North Carolina.

You really cannot go wrong with getting your hands on one of these cables. Be it for your home, office, dormitory, or small business - you are sure to be able to get one that will work for you. With FireFold’s lifetime warranty, you can rest assured that we will help you get the cable swapped out if it ever has manufacturer issues.

Vextra VC64B solid CMR Cat6 Ethernet cable is perfect for commercial and home networking, internet, control and monitoring circuitry and telephone lines. Solid 23AWG copper conductors and quality American-made manufacturing ensure a reliable connection every time.

2U wall mount bracket for installation of patch panels or other 19" rack mount devices. Hinged for easy access to wiring

This 48 port blank patch panel from Vertical Cable accepts standard keystone jacks and inserts to provide custom configurations. It is constructed of heavy duty 16 gauge steel with flame retardant material and is built to last. The included cable manager snaps easily onto the back of the panel, offering integrated wire organization where desired.

Package Includes

• (1) 48 Port Blank Patch Panel with Cable Manager
• (48) Clear Nylon Cable Ties
• (4) Screws

Closing the Distance

The USB cable you have not quite long enough for the task at hand? Well, we’ve got you covered here at FireFold! We have a wide variety of USB extension cables. We have a pretty decent size selection of lengths and a handful of colors with our USB extension cables that are sure to fit what you’re trying to do. Printer not close enough? No problem! Grab one of these USB extension cables and you’re all set.

Don’t stop your consideration of this product at our printer example! These USB cable extensions can be used with a variety of products. Game controller for your PS3 not long enough? Here you go. Wired USB keyboard or mouse just not far enough for you? Tada! The possibilities are endless when you sit back and think about all of the products available on the market that use USB.

Extend Away

Each of our USB active extension cables are rated for USB 2.0, able to handle hi-speed 480Mbps transmission with no issues at all. This is 40 times faster than the previous USB 1.1, though these cables are still backwards compatible with that previous level of USB. With this specific cable, you also get a repeater that will help boost the USB signal you are sending. Up to five repeater cables can be cascaded to increase your distance by up to 75 feet (15ft cable) or 150 feet (30ft cable).

The actual process of extending out your USB cable is pretty simple. Get one of these USB cable extensions, plus your current USB cable into the female end of this cable, and then plug the male end of this cable into your charging adapter or computer. That’s it! The extension is complete and plug-and-play should begin!

With FireFold’s lifetime warranty, you absolutely cannot go wrong with grabbing a few of these cables for your home or business. With such a variety of tasks they can help you with extending out, you are sure to need one on hand from time to time. With a price that most places cannot beat, how can you say no?

The TP-Link TL-SF1016D 16-Port 10/100Mbps Desktop Switch is ideal for small office and home office setups. All sixteen ports utilize auto MDI/MDIX, making it plug and play without regard to cable type. Green energy-efficient technology means you can save up to 80% power consumption of similar switches.

The Cat3 Keystone Jack

The Cat3 jack is a widely used keystone for basic voice applications. The Cat3 jack provided by FireFold is designed to provide excellent performance and durability. This Cat3 jack comes with an RJ11/RJ12 Keystone head and is a 6-position, 6-conductor keystone jack. RJ11 keystone jacks have been replaced for most data transfers for the newer RJ45 ended cables in Cat5 and Cat6 cabling standards.

These specific RJ11 keystone jacks require a tool for their cable installation. However, there is an excellent universal writing system label that allows for hassle-free wiring. So, no worries! You’ll be setting these up with ease in no time.

Meeting All Requirements

Each RJ11 keystone jack is flame retardant and meets current standards through TIA/EIA-568. This phone jack standard applies to commercial building cabling for telecom products. As well, each is ETL verified for quality and safety.

These RJ11 jacks are 14.5mm wide by 16mm high and are easily able to fit in most standard keystone jack wall plates. It should be noted that these RJ11 keystones will also work with most patch panels and surface mount boxes, not just wall plates alone.

You can find a variety of keystone wall plates with us, which allow you to customize easily what you put into each wall plate in your home. You could combine one of these with a coax keystone, or even an RJ45 keystone, with just an easy snapping of each keystone into their place.

Quality to Last a Lifetime

All FireFold keystone jacks come with a lifetime warranty. So, if something goes awry, and it is the product causing the issue, we’ll be more than happy to replace it for you - hassle free! Go ahead and get your hands on one, or many, of these today!

Please note: Slight hue variations may occur between keystone jacks and the matching keystone wall plates. If you need to ensure there is no variation, please contact customer service at 704-979-7100 before placing your order.

The Cat6A Keystone Jack

The Cat6A jack is the most widely used keystone jack in today’s market for networking wall plate solutions or patch panels. Each Cat6A jack provided by Vertical Cable provides outstanding performance, exceeding the TIA/EIA-568-B.2-10 industry standard. Because of this standard, these Cat6a jacks support the operation of 10Gig Ethernet applications. This makes these keystone jacks perfect for use in today’s high-speed networks while remaining completely backward compatible with all previous standards.

The Cat6A jack comes with a standard RJ45 plug on the outside. Wiring slots are in place for a tool required termination. All of our networking keystone jacks have 568A and 568B color codes on the jacks in addition to the easy trouble free 110 style termination.

These network jacks are designed with a shielded termination cap that minimizes additional AXT from neighboring connectors. They also feature twisted pair separation posts which minimize untwisting of pairs to allow for efficient installation and long-term peak performance.

Meeting All Requirements

Each RJ45 keystone jack is flame retardant, and each is UL verified for quality and safety. These RJ45 jacks easily fit in most standard keystone jack wall plates. Plus, they come in a variety of colors - both to help you keep your cables organized but also to allow you to match your keystone easily to whatever colors you are planning.

You can find a variety of keystone wall plates with us, which allow you to customize easily what you put into each wall plate in your home. You could combine one of these with a coax keystone, or even an RJ11 keystone, with just an easy snapping of each keystone into their place.

Quality to Last a Lifetime

All FireFold keystone jacks come with a lifetime warranty. So, if something goes awry, and it is the product causing the issue, we’ll be more than happy to replace it for you - hassle free! Go ahead and get your hands on one, or many, of these today!

Please note: Slight hue variations may occur between keystone jacks and the matching keystone wall plates. If you need to ensure there is no variation, please contact customer service at 704-979-7100 before placing your order.

Vertical Cable SKUs

• Almond 353-V2812/C6AAL
• Black 353-V2813/C6ABK
• Blue 353-V2814/C6ABL
• Green 353-V2815/C6AGR
• Beige 353-V2817/C6AIV
• Orange 353-V2818/C6AOR
• Red 353-V2820/C6ARD
• White 353-V2821/C6AWH
• Yellow 353-V2822/C6AYL

FireFold’s Category 6 (CAT6A Ethernet Cable) shielded Ethernet cables are made to meet market standards and assure the best performance in today’s high-speed networks. CAT6a shielded cables are backwards compatible with any 10BaseT or 100BaseT network cards and hubs, allowing you to change out your old cables for these without having to change out your equipment.

Cat6a is the latest standard that can run up to a 600 MHz frequency, transferring up to 10-Gigabits through appropriate equipment. The Cat6a shielded cables still hold a 50-micron gold plated contact within the RJ45 connectors, just as all of FireFold’s Ethernet cables to help prevent corrosion. A boot rests upon each connector, helping prevent snags and damage to your cable.

These CAT6a shielded cables are constructed from four 26 AWG shielded twisted pair pure copper wire strands in a PVC cable casing. The SSTP (screen shielded twisted pair) wires of these Cat6a patch cables are twisted together to reduce cross talk and the individual pairs have shielding around them. The pairs as a unit have an additional braided screen around them.

With a variety of lengths available, you can get the perfect Cat6a patch cable to meet your needs and get your network setup with ease. You can run lengths of up to 328 feet with these cables.

This is an RJ11 Plug for Stranded Flat Wire. These are designed for voice applications and most commonly used to terminate telephone lines. This connector contains gold plated contacts and uses the 6 Position 4 Conductor wiring standard.

These 10 Gigabit fiber optic cables are backward compatible with existing equipment. They feature almost three times the bandwidth of traditional 62.5/125 multimode fiber.

FireFold’s Category 6 (CAT6 Ethernet cable) Ethernet cables are made to be at market standards, meeting and exceeding the TIA/EIA-568 standard. Each of these Cat6 patch cables are able to perform up to 550 MHz with a 50 micron gold plated contact RJ45 connector at either end of the cable to help against corrosion.

The CAT6 Ethernet cables are constructed from four flat 32 AWG stranded pair pure copper wire strands in a PVC cable casing. This means that the cables are more flexible and more readily usable for patch cables.

The PVC jacket that wraps around these cables is CM type, which means it is good for general use. The jacket itself is flatter than most, making it easier to run under carpeting or around baseboards. A molded strain relief boot rests upon each connector, helping prevent snags and damage to your cable.

CAT6 Ethernet cables are backwards compatible with any 10BaseT or 100BaseT network cards and hubs, allowing you to buy our cables and not have to switch out your older equipment. This simplifies nearly any network setup. Please note, however, that you must upgrade your equipment in order to take full advantage of the higher frequency and transfer rates.

The Enhanced Performance You Need When It Couldn't Be More Important

Anyone who has worked with networking equipment for any appreciable length of time can tell you that more often than not, the ongoing success of a network has less to do with any one major decision and is more about a series of smaller and more important ones. One of these has to do with the quality of the cabling that you use - something that you cannot afford to view as an afterthought any longer.

When you demand performance, flexibility and ingenuity all rolled into one convenient product, what you're really looking for is the Cat5E Patch Cable from FireFold. Our unique brand of Category 5 Enhanced snagless Ethernet cables aren't just designed to meet TIA/EIA-586 standards - with performance at up to 350 MHz in most cases, they often exceed them in the way that you can depend on.

For many, the best part of our cables is that they're already fully backwards compatible with any 10BaseT or 100BaseT networking cards and hubs that you may happen to have. This means that you can upgrade to our superior quality cables for all of the performance benefits they bring with them WITHOUT having to switch out your older equipment as a result.

But even going beyond that, our Cat5E Patch Cable options are fully constructed from four 24 AWG unshielded twisted pure copper wire strands in a sleek, convenient CMR rated PVC jacket. This means that they're absolutely approved for nearly any general indoor application that you may be working with.

The molded strain relief boot itself is also attached right at the connector, which will prevent snags and other events that could damage your cable either during installation or while performing routine troubleshooting and maintenance later on. Not only that, but our RJ-45 connectors all have 50 micron gold plated contacts - something that virtually guarantees that corrosion is NOT something you have to worry about any longer.

As is true with all of our other patch cable products, our Cat5E Ethernet Patch Cables also come complete with a lifetime warranty, a full 60 day money back guarantee and same day shipping in most situations. You'll also have the full might of our industry leading customer support team to turn to in the event that you should run into any issues.

This 1000ft Cat5E Solid Cable with copper clad aluminum conductors is an affordable solution to extensive networking installs. It features easy-to-identify color-striped pairs, rip cord, and a convenient pull-box that helps avoid kinking and bends.

This cable meets TIA/EIA-568B.2, ISO/IEC 11801 standards and is RoHS compliant.

This FTP (foiled twisted pair) cable is perfect for any indoor networking application in a noisy environment. This rating of cable contains a shielding designed to resist crosstalk and electromagnetic interference that comes with networking in close proximity to other cable sources.

Category 6

The next step up from standard Cat5E cable, Category 6 (Cat6) is a "twisted pair" network cable used for carrying data signals at speeds of up to 550MHz of Bandwidth. This cable is preferred for more advanced networking installations where a higher bandwidth than normal is required.

PVC Jacket

Our Cat6 Solid Bulk Cable comes wrapped in a sturdy PVC (Polyvinyl Chloride) Jacket, built to withstand high levels of stress, pulling, and pushing.

FTP (foiled twisted pair)

This type of cable comes complete with a Foil Shielding, to protect the signal strength of the cable and ensure that there is no signal loss due to nearby electrical equipment, or cross-talk from additional cables in close proximity.

23 AWG

For this particular cable, the gauge is 23 AWG, which is a diameter of about 0.0226 Inches, or 0.573mm. 23AWG is the Industry Standard for any typical network cable installation. American Wire Guage (AWG) is the standardized gauging system for measuring wire sizes.

Solid Cable Design

Designed for more straight-forward, simple installation, this particular style of Solid cable is perfect for most installations where cable runs do not require several bends and twists in the line.

The Cat5e Keystone Jack

The Cat5 Jack is the most widely used keystone jack in today’s market for networking wall plate solutions or patch panels. Each Cat5 Jack provided by FireFold provides outstanding performance, exceeding the TIA/EIA 568-B industry standard. This makes these keystone jacks perfect for use in today’s high-speed networks while remaining completely backwards compatible with all previous standards.

These Cat5 Jacks fit into RJ45 Wall plates, Patch Panels, or any standard RJ45 slot. They are perfect for connecting two patch cords without any punching down. Great for an application where you would be switching around wires on both sides of the keystone location.

Meeting All Requirements

Each RJ45 keystone jack is flame retardant and each is UL verified for quality and safety. These RJ45 jacks are 14.5mm wide by 16mm high and are easily able to fit in most standard keystone jack wall plates. Plus, they come in a variety of colors - both to help you keep your cables organized but to also allow you to match your keystone easily to whatever colors you are planning.

You can find a variety of keystone wallplates with us, which allow you to easily customize what you put into each wall plate in your home. You could combine one of these with a coax keystone, or even an RJ11 keystone, with just an easy snapping of each keystone into their place.

Please note: Slight hue variations may occur between keystone jacks and the matching keystone wall plates. If you need to ensure there is no variation, please contact customer service at 704-979-7100 before placing your order.

Perfect for any networking application where Plenum Rated network cable is a requirement. FireFold's Cat6 Plenum Rated Bulk Cable is a must-have for any extensive networking installation.

Plenum Rated Cat6 cable contains a flame retardant PVC jacket and is designed for cable runs being laid in spaces defined as "Air Plenums", this includes raised flooring systems, air handling ducts, etc. Plenum jackets produce less smoke than traditional PVC jackets.

Designed for more straight-forward, simple installtions, this particular style of Solid cable is perfect for most installations where cable runs do not require several bends and twists in the line.

For this particular cable, the gauge is 23 AWG, which is a diameter of about 0.0226 Inches, or 0.573mm. 23 AWG is the Industry Standard for any typical network cable installation. American Wire Guage (AWG) is the standardized gauging system for measuring wire sizes.

Since bulk cable is generally used in intervals, the box that it comes in is almost as important as the cable itself. This is the reason why our boxes are reinforced to provide excellent protection and are made with a simple pull-through design to keep your bulk cable free of kinks and knots while being pulled from the box.

Tiny But Powerful

Our Cat6 Patch Panel is designed to provide amazing performance and cable management. Each Cat6 Patch Panel comes with 110-type termination while meeting and exceeding TIA/EIA-568B.2/568B.2-1 Cat.6 ISO/IEC 11801 hardware specifications.

Compared to standard patch panels, this mini patch bay weighs in at under a pound. It comes with its own mounting bracket, allowing you to easily get this IT patch panel up, out of the way, and ready to go.

Simple to Use

These IT patch panels are able to handle wire diameters of 22AWG to 26AWG, so you should be able to easily find wires to fit. Plus, with entry access available from the top, bottom, and side - you can still easily access your cables once everything is setup.

Compacted Perfection

Each patch bay is a high-density panel design, made for saving space.

Perfect for cable runs involving several twists and turns, Cat6 Stranded 1000' Bulk Cable is perfect for any networking application where a flexible cable is needed. FireFold's Cat6 Stranded Bulk Cable is a must-have for the more specific networking installation where a higher level of bandwidth is needed.

Stranded Cable Design

Designed for cable runs with several bends and twists in the line, a stranded wire is more flexible than solid wire, allowing for a higher resistance to metal fatigue.

Category 6

The next step up from standard Cat5E cable, Category 6 (Cat6) is a "twisted pair" network cable used for carrying data signals at speeds of up to 550MHz of Bandwidth. This cable is preferred for more advanced networking installations where a higher bandwidth than normal is required.

PVC Jacket

Our Cat6 Solid Bulk Cable comes wrapped in a sturdy PVC (Polyvinyl Chloride) Jacket, built to withstand high levels of stress, pulling, and pushing.

24 AWG

For this particular cable, the gauge is 24 AWG, which is a diameter of about 0.0201 Inches, or 0.511mm. 24AWG is the Industry Standard for any typical network cable installation. American Wire Guage (AWG) is the standardized gauging system for measuring wire sizes.

Pull-Through Design

Since bulk cable is generally used in intervals, the box that it comes in is almost as important as the cable itself. This is the reason why our boxes are reinforced to provide excellent protection and are made with a simple pull-through design to keep your bulk cable free of kinks and knots while being pulled from the box.

The Cat6 Keystone Jack

The Cat6 Jack is the most widely used keystone jack in today’s market for networking wall plate solutions or patch panels. Each Cat6 Jack provided by FireFold provides outstanding performance, exceeding the ANSI/TIA/EIA-568-B.2 industry standard. This makes these keystone jacks perfect for use in today’s high-speed networks while remaining completely backward compatible with all previous standards.

These Cat6 Jacks fit into RJ45 wall plates, patch panels, or any standard RJ45 slot. They are perfect for connecting two patch cords without any punching down. Great for an application where you would be switching around wires on both sides of the keystone location.

Meeting All Requirements

Each RJ45 keystone jack is flame retardant and each is UL verified for quality and safety. These RJ45 jacks are 14.5mm wide by 16mm high and are easily able to fit in most standard keystone jack wall plates. Plus, they come in a variety of colors - both to help you keep your cables organized but to also allow you to match your keystone easily to whatever colors you are planning.

You can find a variety of keystone wallplates with us, which allow you to easily customize what you put into each wall plate in your home. You could combine one of these with an HDMI keystone, or even an RJ11 keystone, with just an easy snapping of each keystone into their place.

Please note: Slight hue variations may occur between keystone jacks and the matching keystone wall plates. If you need to ensure there is no variation, please contact customer service at 704-979-7100 before placing your order.

The Cat5e Keystone Jack

The Cat5 Jack is the most widely used keystone jack in today’s market for networking wall plate solutions or patch panels. Each Cat5 Jack provided by FireFold provides outstanding performance, exceeding the TIA/EIA 568-B industry standard. This makes these keystone jacks perfect for use in today’s high-speed networks while remaining completely backward compatible with all previous standards.

The Cat5 jack provided by us comes with a standard RJ45 plug on the outside. These ethernet jacks are toolless. The unique toolless design does not require the use of a punch down tool. This can make things substantially faster when having to put many of these RJ45 jacks into place. All of our networking keystone jacks have 568A and 568B color codes on the jacks in addition to the easy trouble free termination.

Meeting All Requirements

Each RJ45 keystone jack is flame retardant and each is UL verified for quality and safety. These RJ45 jacks are 14.5mm wide by 16mm high and are easily able to fit in most standard keystone jack wall plates. Plus, they come in a variety of colors - both to help you keep your cables organized but to also allow you to match your keystone easily to whatever colors you are planning.

You can find a variety of keystone wallplates with us, which allow you to easily customize what you put into each wall plate in your home. You could combine one of these with an HDMI keystone, or even an RJ11 keystone, with just an easy snapping of each keystone into their place.

Please note: Slight hue variations may occur between keystone jacks and the matching keystone wall plates. If you need to ensure there is no variation, please contact customer service at 704-979-7100 before placing your order.

The TL-SG1005D 5-port Gigabit Ethernet Switch provides you with a high-performance, low-cost, easy-to-use, seamless and standard upgrade to improve old network to 1000Mbps network. Increase the speed of your network server and backbone connections, or make Gigabit to the desktop a reality. Power users in the home, office, workgroup, or creative production environment can now move large, bandwidth-intensive files faster. Transfer graphics, CGI, CAD, or multimedia files and other applications that have to move large files across the network almost instantly.

TL-SG1005D adopts Green Ethernet technology. It can automatically power down ports that have no link, and budget power output for different cable length. With Green Ethernet technology, T:-SG1005D can help you save power and network cost.

Have the need for bulk cable, but don't need the whole box? FireFold has the answer for you! Bulk cable sold by the foot. This cable will be rolled out to your exact requested length.

Bulk (1000 ft) category 6 cable that has a bandwidth of 550 Mhz. The box is reinforced and allows for easy distribution of cable. Lining this cable is PVC material, which is durable yet flexible.

This cable offers speed. Since media is becoming very rich and on demand in today's networks, this extra bandwidth--nearly double of Cat5-- allows Cat 6 to be used on networks that are optimized for high bit rates.

Since bulk cable is normally used in intervals, the box that it comes in is almost as important as the cabling. Our boxes are reinforced to generally protect the cable. Also, they are easy to pull allowing the cable to be virtually kink less while being pulled out of the box.

PVC jackets are very common in networking cables and ours is no exception. This material is strong, protective, and flexible which are the characteristics desired in cables.

Thanks to the fact that so much of our personal and professional lives now revolve around the Internet, to say that the quality of the networks that we depend on every day is important is a little bit of an understatement. Regardless of the size of the network you're constructing or even the environment that you're working in, anything less than the best just won't do in terms of your Cat6 Ethernet cable selections. For the jobs that matter most, FireFold is proud to lead the charge and offer some of the finest options available in that regard that money can buy.

With a performance of up to a stunning 550 MHz, our Cat6 Patch cable selections guarantee the speed, the versatility and the ingenuity you need when you need them the most. All of these cables feature not only an enhanced electrical performance (designed to support all of today's bandwidth-heavy applications), but they're also backwards compatible with any 10BaseT or 100BaseT network cards and hubs that you may currently be using.

All of these cables are constructed from four superior quality unshielded twisted pairs of 24 AWG stranded copper, complete with a sophisticated and rugged PVC jacket. The UTP wires themselves go a long way towards reducing the types of cross-talk that you're likely to experience in certain situations, all while helping to boost signal quality and data transmission at the exact same time. Even the RJ45 connectors have exceptional 50 micron gold plated contacts that are intended to help resist corrosion and degradation for years to come.

Not only that, but the molded strain relief boots present in our Cat6 Ethernet cable options help to avoid snags, tears and other issues during installation or maintenance that could potentially damage your cable over time. Make no mistake: these are molded in a very particular way not only to guarantee the flexibility you demand, but to also resist everyday wear and tear in a way that allows these cables to stand the test of time for years to come.

All Cat6 Ethernet cable options from FireFold come complete with a 60 day money back guarantee, a lifetime warranty and much, much more.

The Enhanced Performance You Need When It Couldn't Be More Important

Anyone who has worked with networking equipment for any appreciable length of time can tell you that more often than not, the ongoing success of a network has less to do with any one major decision and is more about a series of smaller and more important ones. One of these has to do with the quality of the cabling that you use - something that you cannot afford to view as an afterthought any longer.

When you demand performance, flexibility and ingenuity all rolled into one convenient product, what you're really looking for is the Cat5E Patch Cable from FireFold. Our unique brand of Category 5 Enhanced snagless Ethernet cables aren't just designed to meet TIA/EIA-586 standards - with performance at up to 350 MHz in most cases, they often exceed them in the way that you can depend on.

For many, the best part of our cables is that they're already fully backwards compatible with any 10BaseT or 100BaseT networking cards and hubs that you may happen to have. This means that you can upgrade to our superior quality cables for all of the performance benefits they bring with them WITHOUT having to switch out your older equipment as a result.

But even going beyond that, our Cat5E Patch Cable options are fully constructed from four 24 AWG unshielded twisted pure copper wire strands in a sleek, convenient CMR rated PVC jacket. This means that they're absolutely approved for nearly any general indoor application that you may be working with.

The molded strain relief boot itself is also attached right at the connector, which will prevent snags and other events that could damage your cable either during installation or while performing routine troubleshooting and maintenance later on. Not only that, but our RJ-45 connectors all have 50 micron gold plated contacts - something that virtually guarantees that corrosion is NOT something you have to worry about any longer.

As is true with all of our other patch cable products, our Cat5E Ethernet Patch Cables also come complete with a lifetime warranty, a full 60 day money back guarantee and same day shipping in most situations. You'll also have the full might of our industry leading customer support team to turn to in the event that you should run into any issues.

The ICC IC107E5C Cat5E EZ Modular Keystone Jack 25 Pack consists of 25 8-position, 8-conductor (8P8C) connector jacks in blue. These modular jacks are designed to provide outstanding performance in data networks that require maximum speed and bandwidth. They come packaged in a resealable bag with an area for labeling to keep them organized and separate from other jacks.

Tiny But Powerful

Our Cat5E Patch Panel is designed to provide amazing performance and cable management. Each Cat5E Patch Panel comes with 110-type termination while meeting and exceeding EIA/TIA TSB-40 Cat5E connecting hardware specifications.

This is one of our mini patch panels. Compared to the regular patch panel, this patch bay weighs in at under a pound. It comes with its own mounting bracket, allowing you to easily get this IT patch panel up, out of the way, and ready to go.

Simple to Use

Besides the 110 termination that this network patch panel offers, there are 12 individual Cat5E ports on the front side. Once you get your cables terminated on the one side, you just plug and go on the other. This is a very quick and easy solution for being able to swap out devices at any time. Plus, with numbered ports, you can easily keep track of what is plugged in where for better organization.

These IT patch panels are able to handle wire diameters of 22AWG to 26AWG, so you should be able to easily find wires to fit.

Compacted Perfection

Each patch bay is a high-density panel design. The actual physical dimensions of this product are 10 inches by 2.25 inches by 1.75 inches, giving you plenty of space to work with after you get it set up.

These network panels meet TIA/EIA-568B.2/568B.2-1 Cat.5E ISO/IEC 11801 and EN 50173-1 specifications, so they are up to the latest standards. UL certified, they have been also tested to the highest standard for safety.

When installing a wall plate isn't practical, these surface mounts will do the trick. They're convenient, simple, and help maintain that professional look.

The compact, space-saving design is easy to install and come installed with one or two Cat5E Keystone Jacks. Each surface mount comes individually packaged with screws and padded dual sided tape.

The ICC High Density Blank Patch Panel comes equipped with pre-numbered ports. It features a flush mount design that adds stability to your installation with a rigid fit. It is designed to fit standard 19" racks and cabinets.

Vertical Cable 064 Series 1000ft Cat6A 10GS Shielded Solid Network Cable is a high-performance data communications cable capable of 10GS high-speed applications. It is riser-rated for indoor use and arrives on a wooden spool. Sequential foot markings on the jacket allow quick and easy measuring and installation.

Short on USB ports? This USB-C hub is a convenient plug and play solution to adding USB 3.0 ports to your laptop, Macbook, Chromebook Pixel, and so many more devices with Type C support. Simply connect the male USB Type C plug to your computer, then connect up to four separate USB devices using the Type A jacks.

One of the great things about this USB-C dock is that it supports SuperSpeed USB 3.0 with up to 5 Gbps transmission speed. It's backwards compatible with USB 2.0, so legacy devices connect like a breeze. It's USB bus powered, so no additional power supply is needed for operation.

The ICC Cat6 Patch Panel offers an economical solution to achieving superior performance in data networks. It comes preconfigured for T568A and T568B wiring and exceeds ANSI/TIA-568 Category 6 standards.

Thanks to the fact that so much of our personal and professional lives now revolve around the Internet, to say that the quality of the networks that we depend on every day is important is a little bit of an understatement. Regardless of the size of the network you're constructing or even the environment that you're working in, anything less than the best just won't do in terms of your Cat6 Ethernet cable selections. For the jobs that matter most, FireFold is proud to lead the charge and offer some of the finest options available in that regard that money can buy.

With a performance of up to a stunning 550 MHz, our Cat6 Patch cable selections guarantee the speed, the versatility and the ingenuity you need when you need them the most. All of these cables feature not only an enhanced electrical performance (designed to support all of today's bandwidth-heavy applications), but they're also backwards compatible with any 10BaseT or 100BaseT network cards and hubs that you may currently be using.

All of these cables are constructed from four superior quality unshielded twisted pairs of 24 AWG stranded copper, complete with a sophisticated and rugged PVC jacket. The UTP wires themselves go a long way towards reducing the types of cross-talk that you're likely to experience in certain situations, all while helping to boost signal quality and data transmission at the exact same time. Even the RJ45 connectors have exceptional 50 micron gold plated contacts that are intended to help resist corrosion and degradation for years to come.

Not only that, but the molded strain relief boots present in our Cat6 Ethernet cable options help to avoid snags, tears and other issues during installation or maintenance that could potentially damage your cable over time. Make no mistake: these are molded in a very particular way not only to guarantee the flexibility you demand, but to also resist everyday wear and tear in a way that allows these cables to stand the test of time for years to come.

All Cat6 Ethernet cable options from FireFold come complete with a 60 day money back guarantee, a lifetime warranty and much, much more.