Under $25

When low voltage cables are installed through wood studs during construction, there's always the potential someone can accidentally cut, nail or drill through them. Now, make sure your wiring doesn't get damaged with a steel safety plate from Garvin Industries. These plates are designed to be hammered into upright wood studs to ensure no one can penetrate through to the cables. They have built-in prongs to attach to the stud, so you don't even need additional nails or screws. They're quick and easy to install and keep you from having to replace and re-run wiring.

Package Includes

• (10 or 100 ) Steel Safety Plate in your choice of 3 or 6 inch length

When you've got a knockout on a metal enclosure or surface, you have the potential for snagged or nicked cables on sharp edges. Enter plastic knockout insulating bushings from Garvin. This cost-effective cable management solution snaps right into place, so pulling cables through won't loosen it. It's available sized for 1/2, 3/4, 1, 1 1/4, and 1 1/2 inch knockouts.

Package Includes

• (1) Garvin Plastic Knockout Bushing in your choice of knockout size

Garvin WBF-1 Low Volt Box Eliminator Ring

Help Eliminate Gangs

Limited wall room but need a wall plate? This product will eliminate the large gang box, allowing you to insert into any wall.

Saves Space

With the elimination of a standard gang box, you will be able to work with a deal more room. The blue (gang) box also makes cable management a hassle as thick, inflexible wire won't want to go back in properly. This leads to awkward angles that cause wear and tear and even a distortion in signal. Not all walls can support a regular gang box, and if you need an outlet in that particular place then you are essentially out of luck--unless of course you have one of these.

Garvin LVP1 Gang Cable Plate Flex Opening

Make wire management quick and easy with this cable wall plate from Garvin Industries. The flexible opening allows routing of up to six cables, eliminating the need for wall connections and safely corralling cables while keeping the wall opening covered. The cable pass through wall plate features built-in wings, which attach securely to the back of the drywall. As these wings are molded into the plate, it requires no additional parts for installation.

Garvin 1 Gang Recessed Low Voltage Cable Plate

The Garvin LVP1NP 1 Gang Recessed Low Voltage Cable Plate is a versatile cable management tool. This wall plate allows you to easily route multiple cables through a single opening for a clean, finished look to your installation. It can be mounted upright or upside down to meet your specific requirements and provide the best angle for cable routing. This cable plate includes mounting screws for added convenience.

Stress-Free Installations

The enemy of your enemy is your friend. In the case of running low voltage cables, tension on the wires is a powerful adversary. Networking and fiber optic cables are especially prone to issues when they are allowed to bend. Strain lead to network failure and unnecessary downtime. To avoid hassle, it is important to protect the longevity and reliability of your cables. By using the Garvin JHK-21 "J" Cable Support Hook to replace traditional cable trays, you can eliminate the risk of damaging those sensitive cables over long distances and keep connections healthy for years to come.

Support Groups

Garvin JHK-21 has a solid 1” wide base and smooth, rounded corners to prevent snags while cables are being run. It is recommended that J-hooks be placed no more than 5 feet apart, and they can be attached to a wide variety of surfaces such as beams, studs, and ceilings. The pre-drilled screw hole makes attachment to structures quick and easy. Depending on the quantity and weight of your cables, you may need to space cable supports more frequently as excessive sagging between hooks is not optimal. Cable ties or other wire management types may be used to secure wires into place by running them through the small pre-punched holes on the hook.

The 1-5/16” JHK-21 is rated to hold up to 17 lbs and is wide enough for up to 50 Cat5E or fiber optic cables or 32 Cat6 cables, making them ideal for many networking applications. J-hook cable supports can be combined to create custom installation solutions for large volumes of cable or situations where cables are run to multiple locations.

Stress-Free Installations

The enemy of your enemy is your friend. In the case of running low voltage cables, tension on the wires is a powerful adversary. Networking and fiber optic cables are especially prone to issues when they are allowed to bend. Strain lead to network failure and unnecessary downtime. To avoid the hassle, it is important to protect the longevity and reliability of your cables. By using the Garvin JHK-12 "J" Cable Support Hook to replace traditional cable trays, you can eliminate the risk of damaging those sensitive cables over long distances and keep connections healthy for years to come.

Support Groups

Garvin's JHK-12 has a solid 1” wide base and smooth, rounded corners to prevent snags while cables are being run. It is recommended that J-hooks be placed no more than 5 feet apart, and they can be attached to a wide variety of surfaces such as beams, studs, and ceilings. The pre-drilled screw hole makes attachment to structures quick and easy. Depending on the quantity and weight of your cables, you may need to space cable supports more frequently as excessive sagging between hooks is not optimal. Cable ties or other wire management types may be used to secure wires into place by running them through the small pre-punched holes on the hook.

The 3/4" JHK-12 is rated to hold up to 12 lbs and is wide enough for up to 16 Cat5E or fiber optic cables or 10 Cat6 cables, making them ideal for many networking applications. J-hook cable supports can be combined to create custom installation solutions for large volumes of cable or situations where cables are run to multiple locations.

Stress-Free Installations

The enemy of your enemy is your friend. In the case of running low voltage cables, tension on the wires is a powerful adversary. Networking and fiber optic cables are especially prone to issues when they are allowed to bend. Strain lead to network failure and unnecessary downtime. To avoid the hassle, it is important to protect the longevity and reliability of your cables. By using the Garvin JHK-64 4 Inch "J" Cable Support Hook to replace traditional cable trays, you can eliminate the risk of damaging those sensitive cables over long distances and keep connections healthy for years to come.

Support Groups

Garvin's JHK-64 has a wide base and smooth, rounded corners to prevent snags while cables are being run. It is recommended that J-hooks be placed no more than 5 feet apart, and they can be attached to a wide variety of surfaces such as beams, studs, and ceilings. The pre-drilled screw hole makes attachment to structures quick and easy. Depending on the quantity and weight of your cables, you may need to space cable supports more frequently as excessive sagging between hooks is not optimal. Cable ties or other wire management types may be used to secure wires into place by running them through the small pre-punched holes on the hook.

The 4" JHK-64 is rated to hold up to 30 lbs and is wide enough for up to 300 Cat5 or fiber optic cables or 185 Cat6 cables, making them ideal for many networking applications. J-hook cable supports can be combined to create custom installation solutions for large volumes of cable or situations where cables are run to multiple locations.

J hooks are an economical alternative to cable trays. The JHK-12-BW2 3/4 Inch J Cable Support Hook With Wing For #12 to 1/4 Inch Rod Attachment from Garvin Industries can be attached to beam clamps, clips and other support components. It has a fill rate of up to twenty Cat5E cables and includes a retainer clip.

This durable plastic D Ring from Garvin Industries is designed to support multiple low voltage cables when run along walls or ceilings. The generous five inch inner diameter of this low voltage ring holds up to 250 Cat5E cables. A smooth plastic surface prevents snags and damage to wires.

The star configuration of this plastic knockout bushing protects your cables and gives your job a professional, finished look. The bushing is easy to install. No tools are required, as it simply snaps into the knockout hole. The slits allow easy cable management.

• (1) Plastic Star Configuration Bushing for your choice of 1/2" or 3/4" Knockout

The Garvin KOBR-50 Rubber/Split Open Knockout Insulating Bushing is a rubber bushing designed to protect cables from damage due to knockouts in metal boxes. They're simple to use and require no tools. Simply compress the bushing to fit the opening and you've got instant protection for your wiring.

• (1) Rubber Bushing for 1/2" Knockouts

It's important to protect your low voltage wires against nicks and cuts that can come from the sharp edges of metal studs. These universal metal stud grommets from Garvin are an economical solution to protecting those cables. They don't require any tools to install - simply snap one apart, place inside the standard hole built in to the stud, and snap it back together. You've got an instant routing area for your cables. There is only one size needed to fit the universal cutout, which eliminates the expense and hassle of stocking multiple sizes for different job needs.

Package Includes

• (1) Universal Metal Stud Grommet

This durable metal D Ring from Garvin Industries is designed to support multiple low voltage cables when run along walls or ceilings. The generous two inch inner diameter of this low voltage ring holds up to 75 Cat5E cables. A smooth aluminum surface prevents snags and damage to wires.

This durable plastic D Ring from Garvin Industries is designed to support multiple low voltage cables when run along walls or ceilings. The generous two inch inner diameter of this low voltage ring holds up to 75 Cat5E cables. A smooth plastic surface prevents snags and damage to wires.

This durable metal D Ring from Garvin Industries is designed to support multiple low voltage cables when run along walls or ceilings. The generous eight inch inner diameter of this low voltage ring holds up to 425 Cat5E cables. A smooth steel surface prevents snags and damage to wires.

This durable metal D Ring from Garvin Industries is designed to support multiple low voltage cables when run along walls or ceilings. The generous five inch inner diameter of this low voltage ring holds up to 250 Cat5E cables. A smooth aluminum surface prevents snags and damage to wires.

Stress-Free Installations

The enemy of your enemy is your friend. In the case of running low voltage cables, tension on the wires is a powerful adversary. Networking and fiber optic cables are especially prone to issues when they are allowed to bend. Strain lead to network failure and unnecessary downtime. To avoid hassle, it is important to protect the longevity and reliability of your cables. By using the Garvin JHK-32 2 Inch "J" Cable Support Hook to replace traditional cable trays, you can eliminate the risk of damaging those sensitive cables over long distances and keep connections healthy for years to come.

Support Groups

Garvin's JHK-32 has a wide base and smooth, rounded corners to prevent snags while cables are being run. It is recommended that J-hooks be placed no more than 5 feet apart, and they can be attached to a wide variety of surfaces such as beams, studs, and ceilings. The pre-drilled screw hole makes attachment to structures quick and easy. Depending on the quantity and weight of your cables, you may need to space cable supports more frequently as excessive sagging between hooks is not optimal. Cable ties or other wire management types may be used to secure wires into place by running them through the small pre-punched holes on the hook.

The 2" JHK-32 is rated to hold up to 30 lbs and is wide enough for up to 80 Cat5 or fiber optic cables or 50 Cat6 cables, making them ideal for many networking applications. J-hook cable supports can be combined to create custom installation solutions for large volumes of cable or situations where cables are run to multiple locations.

This durable plastic D Ring from Garvin Industries is designed to support multiple low voltage cables when run along walls or ceilings. The generous three inch inner diameter of this low voltage ring holds up to 150 Cat5E cables. A smooth plastic surface prevents snags and damage to wires.