Clear Multi-Cable Insulated Electrical Power Connectors Dual Entry 8 Port 500-#6 - With our Clear Multi Conductor Insulated Connector, you'll see your termination is right every time

Clear Insulated Electrical Power Connectors Clear Multi-Cable Connector - Dual Entry features include:

• Clear Insulation allows Visual Confirmation that conductor is properly inserted
• Multi-Port 6061-T6 Aluminum Connector - CU9AL Dual Rated for use with Copper and/or Aluminum wire
• Single Piece Clear Molded Insulation with Rugged High-Dielectric Plastisol Dipped Coating is chemical and abrasion resistant
• Pre-filled with Oxide Inhibitor
• Easy Re-Entry for Changes, Inspection or Troubleshooting
• Removable Plugs marked with wire size provide easy access for installation.
• Temperature range of –49°F to 194°F (–45° to 90°C)
• Wire Entry from Either Side of Clear Insulated Connector
• Insulated Aluminum Connector eliminates the need for time consuming manual taping, reducing installation time
• One Wire Per Terminal
• PVC insulation reduces the likelihood & cost of power outages caused by improper or inconsistent insulated connections done manually in the field
• ANSI C119.4 & cULus 486b Listed
• 600 Volt
• Rated for use with 194°F(90°C) Cables
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris Mini Photocontrols Flush Mount 39069

Mini Photocontrols Flush Mount - Our Weatherproof Mini Flush Mount Photocontrols puts your lighting solutions at your fingertips.

Mini Photocontrols Flush Mount features include:

• Replacement For Morris# 71299-71301 EntryWay Fixtures
• Weatherproof Polycarbonate Housing & Lens
• SPST - Normally Open
• 1/2" CDS Photocell
• 30-60 Second Time Delay
• Light Levels: ON: .9 to 1.9 FC OFF: 2.8 To 5.6 FC
• Thermal Switch
• Temperature Range: -40ºF to 158ºF
• Power Consumption Below 1.5 Watts Average
• Relative Humidity: 96%
• Contact position at night is normally closed
• Life Cycle: 6500 Cycles
• 3/8”-18 Thread Nipple with Rubber Gasket and Plastic Locknut
• 6” Leads Exit Rear of Housing for Tight locations
• UL Listed
• Order Qty of 1 = 1 Piece

UF Direct Burial Splice Kits 14-8 AWG UF - These are simple and useful Direct Burial Electrical Splice Kits.

UF Direct Burial Splice Kits 14-8 AWG UF features include:

• Direct burial electrical splice kits save money - simplifies splicing UF cable by obsolescing messy multi part splicing kits
• 600 Volt maximum 221°F (105°C) rating
• Provides a reliable, moisture proof electrical connection for UF cable
• 14/3 or 12/3 minimum to 8/3 maximum
• Seal with heat gun or torch
• Electrical splice kit comes complete with one 4-position brass connector and one 8” piece of water impervious adhesive/sealant heat shrink tubing
• UL486D Listed “Submersible” & Raintight”
• Order Qty of 1 = 1 Kit

#18 - #1 Butt/Branch or #18 - 4/0 In-Line ShakeNSeal Encapsulation Epoxy Resin Splice Kits - These are Fast Easy and Inexpensive Direct Burial and Submersible Electrical Splice Kits.

#18 - #1 Butt/Branch or #18 - 4/0 In-Line ShakeNSeal Encapsulation Epoxy Resin Splice Kits features include:

• Exothermic Epoxy Resin Encapsulation Technology
• UL Listed for Direct Burial & Submersible Splicing Applications
• Durable Impregnable Epoxy Splice kits are Perfect for Above and Below Ground Splicing and Jacket Repair
• Permanent Watertight Seal Protects against Voltage Leakage, Cable Deterioration, & Cable Failure
• Fast Error Proof Setup - Low Viscosity Resin Compound Penetrates Completely Around Splice
• Fungus Resistant
• Stub/Butt/Branch In-Line and Feedthrough Applications
• Rated for use with 194°F(90°C) Cable
• No Tool or Heat Source Required
• UL 486D CSA 198.2 Listed
• 600 Volt maximum
• 67024 Butt/Branch Applications Wire Range is #18 - #1 In-Line Aplication Wire Range is #18 - 4/0
• cULus Listed
• Order Qty of 1 = 1 Piece

Copper Long Barrel 1 Hole Compression Lugs #4 Awg 3/8 Stud - One Hole Copper Compression Lugs for fast reliable electrical cable terminations.

Copper Long Barrel 1 Hole Compression Lug #4 Awg 3/8 Stud features include:

• Single Mounting Hole
• Our One Hole Copper Compression Lugs are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Lugs are Marked with Die Index and Color Codes for easy identification
• Long Barrel Accomodates Multiple Crimps
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris Compression Splices Aluminum Long Cylinder  #2 Awg

Aluminum Long Barrel Compression Splices #2 Awg - Aluminum Compression Splices are Dual Rated for use with both Copper & Aluminum Conductors.

Aluminum Long Barrel Compression Splices #2 Awg features include:

• Aluminum Compression Splices are AL9CU Dual Rated & accept both Aluminum and Copper conductors
• Connector Barrels are coated with Oxide Inhibitor & capped
• Center Stop assures Proper Cable Installation
• Made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• Long Barrel Accomodates Multiple Crimps
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• Aluminum Compression Splices are cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris Compression Splices Aluminum Long Cylinder #4 Awg

Aluminum Long Barrel Compression Splices #4 Awg - Aluminum Compression Splices are Dual Rated for use with both Copper & Aluminum Conductors.

Aluminum Long Barrel Compression Splices #4 Awg features include:

• Aluminum Compression Splices are AL9CU Dual Rated & accept both Aluminum and Copper conductors
• Connector Barrels are coated with Oxide Inhibitor & capped
• Center Stop assures Proper Cable Installation
• Made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• Long Barrel Accomodates Multiple Crimps
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• Aluminum Compression Splices are cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris Swivel Mount Pencil Type Photocontrols - 120V

Pencil Type Photocontrols Swivel Mount 120V - Our Swivel Mount Photo Controls give you versatility.

Pencil Type Photocontrols Swivel Mount 120V features include:

• Weatherproof Polycarbonate Housing & Lens
• 1/2” CDS Light Sensor with Heat Sink
• Thermal Switch
• Thin cylindrical shape Swivel Mount Photo Control fits neatly between twin floodlights or other tight applications
• Swivel Mount Photo Controls typically mounts on fixtures or boxes
• Field adjustable swivel base makes it easy to direct the photocell away from stray light
• “O” ring sealed to prevent water from entering through the knuckle
• Light Levels: ON: .9 to 1.9 FC OFF: 2.8 To 5.6 FC
• Single Pole, Single Throw Switch
• Temperature Range: -40°F – +158°F
• Relative Humidity: 96%
• Power Consumption:1.5 Watts Max
• Life Cycle: 6500 Cycles
• Contact Position at Night is Normally Open
• Standard 1/2” I.P.S. Pipe Thread Nipple
• 6” Color Coded Leads with Wiring Diagram on Control
• UL Listed
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 350 MCM 6 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 350 MCM 6 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Copper Flex Cable Long Barrel 2 Hole Compression Lugs 300 MCM 1/2 Stud 1-3/4" Hole Spacing - One Hole Copper Compression Lugs for fast reliable electrical cable terminations.

Copper Flex Cable Long Barrel 2 Hole Compression Lug 300 MCM 1/2 Stud 1-3/4" Hole Spacing features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Two Mounting Hole
• Our Two Hole Copper Compression Lugs are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Lugs are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Short Barrel 1 Hole Compression Lugs #8 Awg 5/16 Stud- One Hole Copper Compression Lugs for fast reliable electrical cable terminations.

Copper Short Barrel 1 Hole Compression Lug #8 Awg 5/16 Stud features include:

• Single Mounting Hole
• Our One Hole Copper Compression Lugs are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Lugs are Marked with Die Index and Color Codes for easy identification
• Peephole Included for Verification of Proper Strand Insertion
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Aluminum Long Barrel Compression Splices #1 Awg - Aluminum Compression Splices are Dual Rated for use with both Copper & Aluminum Conductors.

Aluminum Long Barrel Compression Splices #1 Awg features include:

• Aluminum Compression Splices are AL9CU Dual Rated & accept both Aluminum and Copper conductors
• Connector Barrels are coated with Oxide Inhibitor & capped
• Center Stop assures Proper Cable Installation
• Made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• Long Barrel Accomodates Multiple Crimps
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• Aluminum Compression Splices are cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Aluminum Long Barrel 1 Hole Compression Lugs 300 MCM 3/8" Stud Size - A One Hole Compression Lug for use with Copper or Aluminum Cables.

Aluminum Long Barrel 1 Hole Compression Lugs 300 MCM 3/8" Stud Size features include:

• One Hole Aluminum Compression Lugs are AL9CU Dual Rated and accept both Aluminum and Copper Conductors
• Connector Barrel is Coated with Oxide Inhibitor & capped
• Aluminum Compression Lug is made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Single Mounting Hole
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris 1 Hole Compression Lugs - 3/0 Awg 3/8" Stud Size

Aluminum Long Barrel 1 Hole Compression Lugs 3/0 Awg 3/8" Stud Size features include:

• One Hole Aluminum Compression Lugs are AL9CU Dual Rated and accept both Aluminum and Copper Conductors
• Connector Barrel is Coated with Oxide Inhibitor & capped
• Aluminum Compression Lug is made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Single Mounting Hole
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris 1 Hole Compression Lugs - 1/0 Awg - 1/2 Stud

Aluminum Long Barrel 1 Hole Compression Lugs 1/0 Awg 1/2" Stud Size - A One Hole Compression Lug for use with Copper or Aluminum Cables.

Aluminum Long Barrel 1 Hole Compression Lugs 1/0 Awg 1/2" Stud Size features include:

• One Hole Aluminum Compression Lugs are AL9CU Dual Rated and accept both Aluminum and Copper Conductors
• Connector Barrel is Coated with Oxide Inhibitor & capped
• Aluminum Compression Lug is made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Single Mounting Hole
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Clear Multi-Cable Insulated Electrical Power Connectors Dual Entry 3 Port 350-#6 - With our Clear Multi Conductor Insulated Connector, you'll see your termination is right every time

Clear Insulated Electrical Power Connectors Clear Multi-Cable Connector - Dual Entry features include:

• Clear Insulation allows Visual Confirmation that conductor is properly inserted
• Multi-Port 6061-T6 Aluminum Connector - CU9AL Dual Rated for use with Copper and/or Aluminum wire
• Single Piece Clear Molded Insulation with Rugged High-Dielectric Plastisol Dipped Coating is chemical and abrasion resistant
• Pre-filled with Oxide Inhibitor
• Easy Re-Entry for Changes, Inspection or Troubleshooting
• Removable Plugs marked with wire size provide easy access for installation.
• Temperature range of –49°F to 194°F (–45° to 90°C)
• Wire Entry from Either Side of Clear Insulated Connector
• Insulated Aluminum Connector eliminates the need for time consuming manual taping, reducing installation time
• One Wire Per Terminal
• PVC insulation reduces the likelihood & cost of power outages caused by improper or inconsistent insulated connections done manually in the field
• ANSI C119.4 & cULus 486b Listed
• 600 Volt
• Rated for use with 194°F(90°C) Cables
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris Clear Insulated Multi-Cable Connector - Dual Entry

Clear Multi-Cable Insulated Electrical Power Connectors Dual Entry 2 Port 2/0-#6 - With our Clear Multi Conductor Insulated Connector, you'll see your termination is right every time

Clear Insulated Electrical Power Connectors Clear Multi-Cable Connector - Dual Entry features include:

• Clear Insulation allows Visual Confirmation that conductor is properly inserted
• Multi-Port 6061-T6 Aluminum Connector - CU9AL Dual Rated for use with Copper and/or Aluminum wire
• Single Piece Clear Molded Insulation with Rugged High-Dielectric Plastisol Dipped Coating is chemical and abrasion resistant
• Pre-filled with Oxide Inhibitor
• Easy Re-Entry for Changes, Inspection or Troubleshooting
• Removable Plugs marked with wire size provide easy access for installation.
• Temperature range of –49°F to 194°F (–45° to 90°C)
• Wire Entry from Either Side of Clear Insulated Connector
• Insulated Aluminum Connector eliminates the need for time consuming manual taping, reducing installation time
• One Wire Per Terminal
• PVC insulation reduces the likelihood & cost of power outages caused by improper or inconsistent insulated connections done manually in the field
• ANSI C119.4 & cULus 486b Listed
• 600 Volt
• Rated for use with 194°F(90°C) Cables
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Clear Multi-Cable Insulated Electrical Power Connectors Dual Entry 8 Port #2-#14 - With our Clear Multi Conductor Insulated Connector, you'll see your termination is right every time

Clear Insulated Electrical Power Connectors Clear Multi-Cable Connector -Dual Entry features include:

• Clear Insulation allows Visual Confirmation that conductor is properly inserted
• Multi-Port 6061-T6 Aluminum Connector - CU9AL Dual Rated for use with Copper and/or Aluminum wire
• Single Piece Clear Molded Insulation with Rugged High-Dielectric Plastisol Dipped Coating is chemical and abrasion resistant
• Pre-filled with Oxide Inhibitor
• Easy Re-Entry for Changes, Inspection or Troubleshooting
• Removable Plugs marked with wire size provide easy access for installation.
• Temperature range of –49°F to 194°F (–45° to 90°C)
• Wire Entry from Either Side of Clear Insulated Connector
• Insulated Aluminum Connector eliminates the need for time consuming manual taping, reducing installation time
• One Wire Per Terminal
• PVC insulation reduces the likelihood & cost of power outages caused by improper or inconsistent insulated connections done manually in the field
• ANSI C119.4 & cULus 486b Listed
• 600 Volt
• Rated for use with 194°F(90°C) Cables
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris Pencil Type Photocontrols Swivel Mount 39062

Pencil Type Photocontrols Swivel Mount 208-277V - Our Swivel Mount Photo Controls give you versatility.

Pencil Type Photocontrols Swivel Mount 208-277V features include:

• Weatherproof Polycarbonate Housing & Lens
• 1/2” CDS Light Sensor with Heat Sink
• Thermal Switch
• Thin cylindrical shape Swivel Mount Photo Control fits neatly between twin floodlights or other tight applications
• Swivel Mount Photo Controls typically mounts on fixtures or boxes
• Field adjustable swivel base makes it easy to direct the photocell away from stray light
• “O” ring sealed to prevent water from entering through the knuckle
• Light Levels: ON: .9 to 1.9 FC OFF: 2.8 To 5.6 FC
• Single Pole, Single Throw Switch
• Temperature Range: -40°F – +158°F
• Relative Humidity: 96%
• Power Consumption:1.5 Watts Max
• Life Cycle: 6500 Cycles
• Contact Position at Night is Normally Open
• Standard 1/2” I.P.S. Pipe Thread Nipple
• 6” Color Coded Leads with Wiring Diagram on Control
• UL Listed
• Order Qty of 1 = 1 Piece

Morris Photocontrols Flush Mount with Wall Plate 39042 

Photocontrols Flush Mount with Wall Plate 208-277V - Our Weatherproof Flush Mount Photocontrols puts your lighting solutions at your fingertips.

Photocontrols Flush Mount with Wall Plate 208-277V features include:

• Weatherproof Polycarbonate Housing & Lens
• Brushed Aluminum Wallplate and Gasket
• SPST - Normally Open
• 1/2" CDS Photocell
• 30-60 Second Time Delay
• Light Levels: ON: .9 to 1.9 FC OFF: 2.8 To 5.6 FC
• Thermal Switch
• Temperature Range: -40ºF to 158ºF
• Power Consumption Below 1.5 Watts Average
• Relative Humidity: 96%
• Contact position at night is normally closed
• Life Cycle: 6500 Cycles
• 3/8”-18 Thread Nipple with Rubber Gasket and Plastic Locknut
• 6” Leads Exit Rear of Housing for Tight locations
• UL Listed
• Order Qty of 1 = 1 Piece

Morris Photocontrols Flush Mount with Wall Plate 39040

Photocontrols Flush Mount with Wall Plate 120V - Our Weatherproof Flush Mount Photocontrols puts your lighting solutions at your fingertips.

Photocontrols Flush Mount with Wall Plate 120V features include:

• Weatherproof Polycarbonate Housing & Lens
• Brushed Aluminum Wallplate and Gasket
• SPST - Normally Open
• 1/2" CDS Photocell
• 30-60 Second Time Delay
• Light Levels: ON: .9 to 1.9 FC OFF: 2.8 To 5.6 FC
• Thermal Switch
• Temperature Range: -40ºF to 158ºF
• Power Consumption Below 1.5 Watts Average
• Relative Humidity: 96%
• Contact position at night is normally closed
• Life Cycle: 6500 Cycles
• 3/8”-18 Thread Nipple with Rubber Gasket and Plastic Locknut
• 6” Leads Exit Rear of Housing for Tight locations
• UL Listed
• Order Qty of 1 = 1 Piece

Morris Photocontrols Flush Mount 39032 208-277V

Photocontrols Flush Mount 208-277V - Our Weatherproof Flush Mount Photocontrols are an excellent fixture mounted lighting control.

Photocontrols Flush Mount 208-277V features include:

• Weatherproof Polycarbonate Housing & Lens
• SPST - Normally Open
• 1/2" CDS Photocell
• 30-60 Second Time Delay
• Light Levels: ON: .9 to 1.9 FC OFF: 2.8 To 5.6 FC
• Thermal Switch
• Temperature Range: -40ºF to 158ºF
• Power Consumption Below 1.5 Watts Average
• Relative Humidity: 96%
• Contact position at night is normally closed
• Life Cycle: 6500 Cycles
• 3/8”-18 Thread Nipple with Rubber Gasket and Plastic Locknut
• 6” Leads Exit Rear of Housing for Tight locations
• UL Listed
• Order Qty of 1 = 1 Piece

Morris Photocontrols Flush Mount 39030 - 120V

Photocontrols Flush Mount 120V - Our Weatherproof Flush Mount Photocontrols are an excellent fixture mounted lighting control.

Photocontrols Flush Mount 120V features include:

• Weatherproof Polycarbonate Housing & Lens
• SPST - Normally Open
• 1/2" CDS Photocell
• 30-60 Second Time Delay
• Light Levels: ON: .9 to 1.9 FC OFF: 2.8 To 5.6 FC
• Thermal Switch
• Temperature Range: -40ºF to 158ºF
• Power Consumption Below 1.5 Watts Average
• Relative Humidity: 96%
• Contact position at night is normally closed
• Life Cycle: 6500 Cycles
• 3/8”-18 Thread Nipple with Rubber Gasket and Plastic Locknut
• 6” Leads Exit Rear of Housing for Tight locations
• UL Listed
• Order Qty of 1 = 1 Piece

Morris Open Circuit Cap Photocontrols Locking Type

Locking Type Photocontrols Open Circuit Cap - Locking Photo Controls secure your light settings.

Locking Type Photocontrols Open Circuit Cap features include:

• Used for temporarily turning off a luminaire with twist lock
• UV Stabilized Polycarbonate Cover
• High Impact Polybutylene Terephthalate Base
• IP65 Protection While Installed
• UL Listed
• Order Qty of 1 = 1 Piece

Morris Shorting Cap with Surge Protection 39058

Locking Type Photocontrols Shorting Cap with Surge Protection - Locking Photo Controls secure your light settings.

Locking Type Photocontrols Shorting Cap with Surge Protection features include:

• Locking Shorting Cap typically used for testing lamp & ballast fixture where twist lock photocell is used
• Surge Protection: 460 Joules; 10,000A
• Clamping Voltage: 820V
• UV Stabilized Polycarbonate Cover
• High Impact Polybutylene Terephthalate Base
• IP65 Protection While Installed
• UL Listed
• Order Qty of 1 = 1 Piece

Morris Shorting Cap with No Surge Protection 39056

Locking Type Photocontrols Shorting Cap No Surge Protection - Locking Photo Controls secure your light settings.

Locking Type Photocontrols Shorting Cap No Surge Protection features include:

• Locking Shorting Cap typically used for testing lamp & ballast fixture where twist lock photocell is used
• UV Stabilized Polycarbonate Cover
• High Impact Polybutylene Terephthalate Base
• IP65 Protection While Installed
• UL Listed
• Order Qty of 1 = 1 Piece

Morris Locking Type Photocontrol Standard 39050 

Locking Type Photocontrol Standard 120V - Locking Photo Controls are perfect for Residential or Commercial Lighting Control.

Locking Type Photocontrol Standard 120V features include:

• Cost effective Means of Controlling Residential Lighting Systems
• 5-20 Second Time Delay
• UV Stabilized Polycarbonate Cover and Clear Window
• High Impact Polybutylene Terephthalate Base
• IP65 Protection While Installed
• 1/2” Light Sensor
• Temp Rate: -40°F to 158°F
• Relative Humidity: 96%
• Power Consumption:1.5 Watts Average
• Electrical Life: 5000 Cycles
• UL Listed
• Order Qty of 1 = 1 Piece

Locking Style Photocontrols Spec Grade 208-277V - Locking Photo Controls are perfect for Utility and Municipal Lighting Control.

Locking Style Photocontrols Spec Grade 208-277V features include:

• Cost effective Means of Controlling Utility, Commercial & Residential Lighting Systems
• 30-120 Second Time Delay
• UV Stabilized Polycarbonate Cover and Clear Window
• High Impact Polybutylene Terephthalate Base
• IP65 Protection While Installed
• 1” Light Sensor
• Temp Rate: -40°F to 158°F
• Relative Humidity: 96%
• Power Consumption:1.5 Watts Average
• Electrical Life: 6500 Cycles
• UL Listed
• Order Qty of 1 = 1 Piece

Spec Grade Photocontrols Locking Type 120V - Locking Photo Controls are perfect for Utility and Municipal Lighting Control.

Spec Grade Photocontrols Locking Type 120V features include:

• Cost effective Means of Controlling Utility, Commercial & Residential Lighting Systems
• 30-120 Second Time Delay
• UV Stabilized Polycarbonate Cover and Clear Window
• High Impact Polybutylene Terephthalate Base
• IP65 Protection While Installed
• 1” Light Sensor
• Temp Rate: -40°F to 158°F
• Relative Humidity: 96%
• Power Consumption:1.5 Watts Average
• Electrical Life: 6500 Cycles
• UL Listed
• Order Qty of 1 = 1 Piece

Locking Style Receptacles withAluminum Bracket Mount For Twist Lock Photoeye - Phenolic Locking Style Receptacles are used for Mounting Locking Style Photocells.

Locking Style Receptacles withAluminum Bracket Mount For Twist Lock Photoeye features include:

• Phenolic Socket
• Brass Contacts
• ABS Waterproof Back Cover
• 1/2” Conduit with Zinc Alloy Locknut
• Temp Rate: -40°F to 176°F
• Relative Humidity : 96%
• cULus Listed
• Order Qty of 1 = 1 Piece

Locking Style Receptacles Fixture Mount For Twist Lock Photoeye - Phenolic Locking Style Receptacles are used for Mounting Locking Style Photocells.

Locking Style Receptacles Fixture Mount For Twist Lock Photoeye features include:

• Phenolic Socket
• Brass Contacts
• ABS Waterproof Back Cover
• Temp Rate: -40°F to 176°F
• Relative Humidity : 96%
• UL Recognized
• Order Qty of 1 = 1 Piece

Shutter Style Photocontrols - Fixed Base - Spec Grade 208-277V - Our Weatherproof Photocontrols have many useful features.

Shutter Style Photocontrols - Fixed Base - Spec Grade 208-277V features include:

• Die Cast Aluminum Vandal Resistant Housing
• 1” Extra Wide Light Sensor for Increased Accuracy
• Photocontrol features a heavy-duty thermal bi-metal switch that provides a 30-60 second time delay. This virtually eliminates unwanted lamp cycling that could be caused by lightning, car headlights, etc
• Although the turn-on level is pre-set at the factory, each control is furnished with an adjustable slide shutter/bar that allows field adjustment
• Typically mount on fixtures or boxes
• Weatherproof Polycarbonate Housing
• Single Pole, Single Throw Switch
• Contact Position at Night is Normally Closed
• Temperature Range: -40°F to 158°F
• Power Consumption Below 1.5 Watts Average
• Standard 1/2” I.P.S. Pipe Threaded Nipple, Includes Gasket and Locknut
• 6" Color Coded Leads with Wiring Diagram on Control
• UL Listed
• Order Qty of 1 = 1 Piece

Shutter Style Photocontrols - Fixed Base - Spec Grade 120V - Our Weatherproof Photocontrols have many useful features.

Shutter Style Photocontrols - Fixed Base - Spec Grade 120V features include:

• Die Cast Aluminum Vandal Resistant Housing
• 1” Extra Wide Light Sensor for Increased Accuracy
• Photocontrol features a heavy-duty thermal bi-metal switch that provides a 30-60 second time delay. This virtually eliminates unwanted lamp cycling that could be caused by lightning, car headlights, etc
• Although the turn-on level is pre-set at the factory, each control is furnished with an adjustable slide shutter/bar that allows field adjustment
• Typically mount on fixtures or boxes
• Weatherproof Polycarbonate Housing
• Single Pole, Single Throw Switch
• Contact Position at Night is Normally Closed
• Temperature Range: -40°F to 158°F
• Power Consumption Below 1.5 Watts Average
• Standard 1/2” I.P.S. Pipe Threaded Nipple, Includes Gasket and Locknut
• 6" Color Coded Leads with Wiring Diagram on Control
• UL Listed
• Order Qty of 1 = 1 Piece

Shutter Style Photocontrol - Swivel Base 208-277V- Our Weatherproof Photocontrols have many useful features.

Shutter Style Photocontrol - Swivel Base 208-277V features include:

• Photocontrol features a heavy-duty thermal bi-metal switch that provides a 30-60 second time delay. This virtually eliminates unwanted lamp cycling that could be caused by lightning, car headlights, etc
• Although the turn-on level is pre-set at the factory, each control is furnished with an adjustable slide shutter/bar that allows field adjustment
• Typically mount on fixtures or boxes
• Weatherproof Polycarbonate Housing
• Single Pole, Single Throw Switch
• Contact Position at Night is Normally Closed
• Temperature Range: -40°F to 158°F
• Power Consumption Below 1.5 Watts Average
• Standard 1/2” I.P.S. Pipe Threaded Nipple, Includes Gasket and Locknut
• 6" Color Coded Leads with Wiring Diagram on Control
• UL Listed
• Order Qty of 1 = 1 Piece

Shutter Style Photocontrol - Swivel Base 120V - Our Weatherproof Photocontrols have many useful features.

Shutter Style Photocontrol - Swivel Base 120V features include:

• Photocontrol features a heavy-duty thermal bi-metal switch that provides a 30-60 second time delay. This virtually eliminates unwanted lamp cycling that could be caused by lightning, car headlights, etc
• Although the turn-on level is pre-set at the factory, each control is furnished with an adjustable slide shutter/bar that allows field adjustment
• Typically mount on fixtures or boxes
• Weatherproof Polycarbonate Housing
• Single Pole, Single Throw Switch
• Contact Position at Night is Normally Closed
• Temperature Range: -40°F to 158°F
• Power Consumption Below 1.5 Watts Average
• Standard 1/2” I.P.S. Pipe Threaded Nipple, Includes Gasket and Locknut
• 6" Color Coded Leads with Wiring Diagram on Control
• UL Listed
• Order Qty of 1 = 1 Piece

Shutter Style Photocontrol - Fixed Base 208-277V - Our Weatherproof Photocontrols have many useful features.

Shutter Style Photocontrol - Fixed Base 208-277V features include:

• Photocontrol features a heavy-duty thermal bi-metal switch that provides a 30-60 second time delay. This virtually eliminates unwanted lamp cycling that could be caused by lightning, car headlights, etc
• Although the turn-on level is pre-set at the factory, each control is furnished with an adjustable slide shutter/bar that allows field adjustment
• Typically mount on fixtures or boxes
• Weatherproof Polycarbonate Housing
• Single Pole, Single Throw Switch
• Contact Position at Night is Normally Closed
• Temperature Range: -40°F to 158°F
• Power Consumption Below 1.5 Watts Average
• Standard 1/2” I.P.S. Pipe Threaded Nipple, Includes Gasket and Locknut
• 6" Color Coded Leads with Wiring Diagram on Control
• UL Listed
• Order Qty of 1 = 1 Piece

Shutter Style Photocontrol - Fixed Base 120V - Our Weatherproof Photocontrols have many useful features.

Shutter Style Photocontrol - Fixed Base 120V features include:

• Photocontrol features a heavy-duty thermal bi-metal switch that provides a 30-60 second time delay. This virtually eliminates unwanted lamp cycling that could be caused by lightning, car headlights, etc
• Although the turn-on level is pre-set at the factory, each control is furnished with an adjustable slide shutter/bar that allows field adjustment
• Typically mount on fixtures or boxes
• Weatherproof Polycarbonate Housing
• Single Pole, Single Throw Switch
• Contact Position at Night is Normally Closed
• Temperature Range: -40°F to 158°F
• Power Consumption Below 1.5 Watts Average
• Standard 1/2” I.P.S. Pipe Threaded Nipple, Includes Gasket and Locknut
• 6" Color Coded Leads with Wiring Diagram on Control
• UL Listed
• Order Qty of 1 = 1 Piece

UF Direct Burial Stretcher Kits 14-8 AWG UF - Direct Burial Electrical Stretcher Kits seal with a heat gun.

UF Direct Burial Stretcher Kits 14-8 AWG UF features include:

• Direct burial electrical stretcher kits eliminate the need for using two connectors and a short piece of cable when repairing damaged UF cable
• 600 Volt maximum 221°F (105°C) rating
• Provides a reliable, moisture proof electrical connection for UF cable
• 14/3 or 12/3 minimum to 8/3 maximum
• Seal with heat gun or torch
• Electrical stretcher kit comes complete with 11-1/2” connector and one 20” piece of water impervious adhesive/sealant heat shrink tubing
• UL486D Listed “Submersible” & Raintight”
• Order Qty of 1 = 1 Kit

Submersible Insulated Streetlighting Connectors Multi-Port Offset #14 - 2/0 3 Port - This Submersible Insulated Streetlighting Connector Offset Multi-Port can be Used in StreetLighting and other Direct Burial and Submersible Applications.

Submersible Insulated Streetlighting Connectors Offset Multi-Port #14 - 2/0 3 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in StreetLight Hand Holes and other Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 4 Port - This Submersible Insulated Streetlighting Connector Multi-Port can be Used in StreetLighting and other Direct Burial and Submersible Applications.

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 4 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in StreetLight Hand Holes and other Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• UL Tested Ambient Temperature Rating Down To 0°F
• cULus Listed
• Order Qty of 1 = 1 Piece

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 3 Port - This Submersible Insulated Streetlighting Connector Multi-Port can be Used in StreetLighting and other Direct Burial and Submersible Applications.

Submersible Insulated Streetlighting Connectors Multi-Port features #14 - 2/0 3 Port include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in StreetLight Hand Holes and other Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• UL Tested Ambient Temperature Rating Down To 0°F
• cULus Listed
• Order Qty of 1 = 1 Piece

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 2 Port - This Submersible Insulated Streetlighting Connector Multi-Port can be Used in StreetLighting and other Direct Burial and Submersible Applications.

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 2 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in StreetLight Hand Holes and other Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• UL Tested Ambient Temperature Rating Down To 0°F
• cULus Listed
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 600 MCM 6 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 600 MCM 6 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 600 MCM 4 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 600 MCM 4 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 600 MCM 3 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 600 MCM 3 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 350 MCM 4 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 350 MCM 4 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 350 MCM 3 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 350 MCM 3 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors In-Line Splice #12 - 350 MCM - This In Line Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

In Line Submersible Pedestal Splice Connectors #12 - 350 MCM features include:

• Designed for use in Direct Burial & Submerible installations such as hand holes, below grade boxes, in the ground or submersed in water
• Range Taking Design Reduces Inventory
• AL9CU Dual Rated for Copper and Aluminum Conductors
• Insulated with High Dielectric Strength Tubber Compound
• Molded for Precise Fit & supplied with removable access plugs over the hex screws
• Eliminates the need for Taping, Heat Shrink, Etc.
• Abrasion and Chemical Resistant, will not support combustion
• UL Listed for Wet or Damp Locations, Direct Burial & Submersible per UL 486D
• Complies with ANSI C119.1 Specifications
• 600 Volts
• cULus Listed
• UL tested Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece