Networking Extenders

The MC200CM is a media converter designed to convert 1000BASE-SX fiber to 1000Base-T copper media or vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-SX standards, the MC200CM is designed for use with multi-mode fiber cable utilizing the SC-Type connector. The MC200CM supports shortwave (SX) laser specification at a full wire speed forwarding rate. It works at 850nm on both transmitting and receiving data.

Intellinet Power over Ethernet (PoE+) Splitter

IEEE802.3at, 5, 7.5, 9 or 12 V DC output voltage

Deliver Power over Ethernet to remote devices

The Intellinet Network Solutions PoE+ Splitter allows you to deliver both data and electrical power to non-PoE Ethernet-enabled products using the Cat5 Ethernet cable. Using the PoE Splitter, you can take advantage of Power over Ethernet and place Ethernet-enabled products, such as Network Cameras and Wireless Access Points*, where power outlets are not readily available.

Simplify Installation for an Ethernet-based Device

Having to manage only an Ethernet cable simplifies the physical installation of the device. Without having to worry about the availability of a power source, you can mount Ethernet-enabled products on a ceiling or outdoors, up to 100m (328 feet)** from a power source. The PoE Splitter is simple to install and requires no tools or software.

802.3af Compliant Power over Ethernet

The PoE Splitter can be used to complement any PoE injector unit or midspan switch to provide small to medium-sized businesses a complete end-to-end PoE solution. This unit supports 802.3af and 802.3at, ensuring compatibility with other 802.3af/t PoE-compliant injector units or PSE switches.

Adjustable Power Output

During the setup, the PoE Splitter can be set to power any compatible 5 V, 7.5 V, 9 V or 12 V Ethernet-enabled device via the volt selector located on the side.

** Maximum distance per 802.3u specifications.

Tenda Gigabit High PoE Injector POE30G-AT

The Tenda PoE30G-AT is the IEEE802.3 AT Gigabit PoE injector, which fully conforms to the standard of wtih 802.3, transmitting power through Ethernet cable, the maximum transmission distance can reach 100 meters. The PoE injector has two Ethernet gigabit data ports and an output port combination of data and power. In addition, the device can be used for Ethernet device IEEE802.3af/ compatible PoE power applications such as wireless AP, VoIP phone and web CAM. The power supply of Ethernet cable not only provides system reliability, traditional power grid expansion, but also simplifies the deployment of power lines.

PoE Performance

PoE ports supports IEEE802.3at and IEEE802.3af standard Supports AT high power(30W)

Power supply distance extension

The standard cat’s power distance can be extended to 100 meters. The device can extend the range of PoE power over long distances, and simplify the deployment of power lines so that PD equipment can supply power.

Gigabit blazing-fast delivery

10/100M/1000Mbps autosensing RJ45 port provides fast data delivery, supports wire speed forwarding and MDI/MDIX, plug and play.

Stable performance

Adopts new chips solution, brings new performance experience, powerful data transfer and power

Enable-IT 24V Outdoor Gigabit Inline PoE Reducer

The EnableIT™ 324 Gigabit PoE Reducer 24V DC Inline Solution is a specialized converter that transforms any high power DC voltage signal down to a 24V DC or optional 12V PoE signal with Gigabit Ethernet LAN data.

This PoE Reducer is essential for installing sensitive low voltage PoE devices like PoE IP cameras, IP Phones or PoE WiFi Access points. Compatible with all 802.3af, 802.3at or PoE switches or standalone injectors including reverse polarity.

This Gigabit Power over Ethernet (PoE) Reducer is a unique one of a kind and world’s first solution that is able to take your hot PoE and PoE Plus power/data at extreme distance and safely deliver 24VDC or 12VDC PoE input for your expensive PoE Equipment.

The overvoltage issue is typically created by PoE injectors and PoE Midspan devices that leverage PoE Extenders over extreme distances and are too strong in delivered output PoE voltage to be inserted into limited 12v/24V PoE devices such as Ubiquity Wireless Access Point radios. These RJ-45 PoE radios were designed for standard Ethernet distance limitation in mind and cannot handle voltage over 20VDC. The Enable-IT 324 now solves that issue with a plug and go Gigabit PoE Reducer so that you can safely leverage PoE Extender kits that support PoE and PoE like the Enable-IT 821P, 828 or 865 PRO PoE Extender Kits.

This elegant unit is ideal for installing any WiFi Wireless Access Point, Security camera or other PoE powered equipment. It eliminates the need for external power supply and its associated AC/DC power cabling, providing a compact, affordable, safe and reliable power solution over your wiring or existing Ethernet infrastructure. The 324 Gigabit PoE Reducer uses industry LAN standard RJ-45 (8-pin) connectors to make installing in most any environment a snap, plug and go simplicity or on your existing or new wiring.

The Enable-IT 324 unit is very lightweight and compact for most all applications and use. These units are easy and rapid to install with plug and play RJ-45 Ethernet jacks to quickly insert your wiring and go. As a 802.3af and 802.3at compliant device, the Enable-IT 324 – 24VDC Power over Ethernet Reducer uses 4 wires in a category rated wiring bundle, i.e. CAT5e run. As will all PoE voltage drops over distance. As a rule of thumb you will lose 6V per every 100′- 200′ of wiring, depending on the gauge. Lower power also means more amperage means more heat and perhaps issues with the 24 gauge wires in CAT5. You may need to use 18 gauge wiring.

Tenda Boost AC1200 Dual-Band Wi-Fi Repeater

A18 is an AC1200 dual-band Wi-Fi repeater dedicated for two-storey houses, villas, and multi-room homes with a coverage area of over 1,300 square feet. It offers up to 300 Mbps data rates on 11n band and 867 Mbps data rates on 11ac band. With two external omni-directional antennas, A18 can provide larger Wi-Fi coverage, high-speed data rates, and support applications such as the playback of 1080P HD videos, massive multiplayer online games, and high-speed downloads. With the upgrade Setup Wizard, it only takes three steps to configure your repeater and is easy to use. A18 also works with other Wi-Fi routers available on the market. For whole-home Wi-Fi coverage, A18 is your best choice.

Tenda AC750 Dual Band WiFi Repeater

A15 is an AC750 dual-band WiFi repeater dedicated for two-storey houses, villas, and multi-room houses with an area over 120 square meters. It offers up to 300 Mbps data rate on 11n band and 433 Mbps data rate on 11ac band. With two external omni-directional antennas, A15 can provide larger WiFi coverage, as well as extreme fast data rate, satisfying applications such as playback of 1080P HD videos, massively multiplayer online games, and high-speed download. With the upgrade Setup Wizard, it only takes you three steps to configure your repeater, which is easy to use. A15 also works better with other brands' WiFi router available on the market. For whole home WiFi coverage, A15 is your best choice.

Swift switchover between 2.4 GHz and 5 GHz bands for stable internet connection with least interruption

With 2 external high-quality omni-directional antennas, A15 can expand 2.4 GHz and 5 GHz WiFi networks simultaneously, supporting automatic switchover of mobile terminals between 2.4 GHz and 5 GHz bands. A15 offers a 300 Mbps 2.4 GHz band that maximizes mobile device connectivity, and a much faster 433 Mbps 5 GHz band that minimizes interference.

Excellent performance within a compact and exquisite design

Compact exterior provides high-quality and long-range WiFi coverage. Working with a dual band WiFi router, A15 allows you to enjoy a smarter life with faster and more stable internet connection

Two modes in one for a variety of scenarios

You can switch between Repeater mode and AP mode as needed.

• Repeater mode: A15 can expand WiFi coverage by bridging the upstream router's WiFi signal, and allows wired devices connected to its LAN port to access the internet;
• AP mode: connect an Ethernet cable with internet connectivity to the LAN port of A15 to turn it into an AP.

Intuitive signal LED to indicate the optimal repeater location

The Signal LED tells the best repeater location.
Blue: good signal strength
Red: poor signal strength
Off: no signal

Compatible with any WiFi router

A15 can work well with any WiFi router and WiFi DSL modem router available on the market, outshining most of repeaters.

What This Product Does

The MC110CS is a media converter designed to convert 100BASE-FX fiber to 100Base-TX copper media and vice versa. Designed under IEEE 802.3u 10/100Base-TX and 100Base-FX standards, the MC110CS is designed for use with single-mode fiber cable utilizing the SC-Type connector. The MC110CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1310nm on both transmitting and receiving data. Auto MDI/MDI-X for TX port, Auto negotiation of duplex mode. The MC110CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 12.5 miles (20km).

What This Product Does

The MC210CS is a media converter designed to convert 1000BASE-LX fiber to 1000Base-T copper media or vice versa. Designed under IEEE802.3ab 1000Base-T and IEEE802.3z 1000Base-LX standards, the MC210CS is designed for use with single-mode fiber cable utilizing the SC-Type connector. The MC210CS supports longwave (LX) laser specification at a full wire speed forwarding rate. It works at 1310nm on both transmitting and receiving data. Auto MDI/MDI-X for TX port, and front panel status LEDs. The MC210CS will transmit at extended fiber optic distances utilizing single-mode fiber up to 9.3 miles (15km).