Electrical - Residential

1/0 - 750 MCM In-Line ShakeNSeal Encapsulation Epoxy Resin Splice Kits - These are Fast Easy and Inexpensive Direct Burial and Submersible Electrical Splice Kits.

1/0 - 750 MCM ShakeNSeal Encapsulation Epoxy Resin Splice Kits features include:

• Exothermic Epoxy Resin Encapsulation Technology
• UL Listed for Direct Burial & Submersible Splicing Applications
• Durable Impregnable Epoxy Splice kits are Perfect for Above and Below Ground Splicing and Jacket Repair
• Permanent Watertight Seal Protects against Voltage Leakage, Cable Deterioration, & Cable Failure
• Fast Error Proof Setup - Low Viscosity Resin Compound Penetrates Completely Around Splice
• Fungus Resistant
• Stub/Butt/Branch In-Line and Feedthrough Applications
• Rated for use with 194°F(90°C) Cable
• No Tool or Heat Source Required
• UL 486D CSA 198.2 Listed
• 600 Volt maximum
• *67028 Not UL Listed
• cULus Listed
• Order Qty of 1 = 1 Piece

#18 - #1 Butt/Branch or #18 - 4/0 In-Line ShakeNSeal Encapsulation Epoxy Resin Splice Kits - These are Fast Easy and Inexpensive Direct Burial and Submersible Electrical Splice Kits.

#18 - #1 Butt/Branch or #18 - 4/0 In-Line ShakeNSeal Encapsulation Epoxy Resin Splice Kits features include:

• Exothermic Epoxy Resin Encapsulation Technology
• UL Listed for Direct Burial & Submersible Splicing Applications
• Durable Impregnable Epoxy Splice kits are Perfect for Above and Below Ground Splicing and Jacket Repair
• Permanent Watertight Seal Protects against Voltage Leakage, Cable Deterioration, & Cable Failure
• Fast Error Proof Setup - Low Viscosity Resin Compound Penetrates Completely Around Splice
• Fungus Resistant
• Stub/Butt/Branch In-Line and Feedthrough Applications
• Rated for use with 194°F(90°C) Cable
• No Tool or Heat Source Required
• UL 486D CSA 198.2 Listed
• 600 Volt maximum
• 67024 Butt/Branch Applications Wire Range is #18 - #1 In-Line Aplication Wire Range is #18 - 4/0
• cULus Listed
• Order Qty of 1 = 1 Piece

Morris Compression Splices Aluminum Long Cylinder  #2 Awg

Aluminum Long Barrel Compression Splices #2 Awg - Aluminum Compression Splices are Dual Rated for use with both Copper & Aluminum Conductors.

Aluminum Long Barrel Compression Splices #2 Awg features include:

• Aluminum Compression Splices are AL9CU Dual Rated & accept both Aluminum and Copper conductors
• Connector Barrels are coated with Oxide Inhibitor & capped
• Center Stop assures Proper Cable Installation
• Made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• Long Barrel Accomodates Multiple Crimps
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• Aluminum Compression Splices are cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Morris Compression Splices Aluminum Long Cylinder #4 Awg

Aluminum Long Barrel Compression Splices #4 Awg - Aluminum Compression Splices are Dual Rated for use with both Copper & Aluminum Conductors.

Aluminum Long Barrel Compression Splices #4 Awg features include:

• Aluminum Compression Splices are AL9CU Dual Rated & accept both Aluminum and Copper conductors
• Connector Barrels are coated with Oxide Inhibitor & capped
• Center Stop assures Proper Cable Installation
• Made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• Long Barrel Accomodates Multiple Crimps
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• Aluminum Compression Splices are cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 350 MCM 6 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 350 MCM 6 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Copper Flex Cable Long Barrel 2 Hole Compression Lugs 300 MCM 1/2 Stud 1-3/4" Hole Spacing - One Hole Copper Compression Lugs for fast reliable electrical cable terminations.

Copper Flex Cable Long Barrel 2 Hole Compression Lug 300 MCM 1/2 Stud 1-3/4" Hole Spacing features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Two Mounting Hole
• Our Two Hole Copper Compression Lugs are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Lugs are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Aluminum Long Barrel Compression Splices #1 Awg - Aluminum Compression Splices are Dual Rated for use with both Copper & Aluminum Conductors.

Aluminum Long Barrel Compression Splices #1 Awg features include:

• Aluminum Compression Splices are AL9CU Dual Rated & accept both Aluminum and Copper conductors
• Connector Barrels are coated with Oxide Inhibitor & capped
• Center Stop assures Proper Cable Installation
• Made of High-Conductivity Seamless Aluminum
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Color Coded for Easy Identification
• Marked with Die Index
• Crimp Marks indicate Proper Crimp Locations
• Long Barrel Accomodates Multiple Crimps
• UL486B Listed AL9CU
• Listed for 35KV when properly installed
• Aluminum Compression Splices are cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Streetlighting Y-Type Mechanical Disconnect Kits #14 - #4 Run #14-#2 - These Streetlighting Y-Type Mechanical Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting Y-Type Mechanical Disconnect Kits #14 - #4 Run #14-#2 features include:

• Streetlighting Y-Type Mechanical Disconnect Kits Provide A Submersible T-Type Splice Solution fro Street and Parking Lot Lighting Applications
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting Y-Type Compression Breakaway Disconnect Kits Non-Fused #4 - #2 - These Streetlighting Y-Type Compression Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting Y-Type Compression Breakaway Disconnect Kits Non-Fused #4 - #2 features include:

• Streetlighting Y-Type Compression Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting Y-Type Compression Breakaway Disconnect Kits Non-Fused #14 - #6 - These Streetlighting Y-Type Compression Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting Y-Type Compression Breakaway Disconnect Kits Non-Fused #14 - #6 features include:

• Streetlighting Y-Type Compression Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting Y-Type Compression Breakaway Disconnect Kits Fused #4 - #2 - These Streetlighting Y-Type Compression Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting Y-Type Compression Breakaway Disconnect Kits Fused #4 - #2 features include:

• Streetlighting Y-Type Compression Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• Accepts Standard Cartridge Fuses 13/32" X 1-1/2" - No Glass Fuses
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting In-Line Compression Breakaway Disconnect Kits Non-Fused #4 - #2 - These Streetlighting In-Line Compression Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting In-Line Compression Breakaway Disconnect Kits Non-Fused #4 - #2 features include:

• Streetlighting In-Line Compression Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting In-Line Compression Breakaway Disconnect Kits Non-Fused #14 - #6 - These Streetlighting In-Line Compression Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting In-Line Compression Breakaway Disconnect Kits Non-Fused #14 - #6 features include:

• Streetlighting In-Line Compression Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting In-Line Compression Breakaway Disconnect Kits Fused #4 - #2 - These Streetlighting In-Line Compression Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting In-Line Compression Breakaway Disconnect Kits Fused #4 - #2 features include:

• Streetlighting In-Line Compression Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• Accepts Standard Cartridge Fuses 13/32" X 1-1/2" - No Glass Fuses
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting Y-Type Non-Fused Mechanical Breakaway Disconnect Kits - These Streetlighting Y-Type Non-Fused Mechanical Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting Y-Type Non-Fused Mechanical Breakaway Disconnect Kits features include:

• Streetlighting Y-Type Mechanical Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting Y-Type Fused Mechanical Breakaway Disconnect Kits - These Streetlighting Y-Type Fused Mechanical Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting Y-Type Fused Mechanical Breakaway Disconnect Kits features include:

• Streetlighting Y-Type Mechanical Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• Accepts Standard Cartridge Fuses 13/32" X 1-1/2" - No Glass Fuses
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits - These Streetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits features include:

• Streetlighting In-Line Mechanical Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Streetlighting In-Line Fused Mechanical Breakaway Disconnect Kits - These Streetlighting In-Line Fused Mechanical Breakaway Disconnect Kits are for Street and Parking Lot Lighting Applications

Streetlighting In-Line Fused Mechanical Breakaway Disconnect Kits features include:

• Streetlighting In-Line Mechanical Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact
• Designed for Use in StreetLight Hand Holes
• Completely Waterproof  Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity
• Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated
• Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature
• Accepts Standard Cartridge Fuses 13/32" X 1-1/2" - No Glass Fuses
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• 30 Amp
• 600 Volts
• Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included
• Order Qty of 1 = 1 Piece

Submersible Insulated Streetlighting Connectors Multi-Port Offset #14 - 2/0 3 Port - This Submersible Insulated Streetlighting Connector Offset Multi-Port can be Used in StreetLighting and other Direct Burial and Submersible Applications.

Submersible Insulated Streetlighting Connectors Offset Multi-Port #14 - 2/0 3 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in StreetLight Hand Holes and other Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 4 Port - This Submersible Insulated Streetlighting Connector Multi-Port can be Used in StreetLighting and other Direct Burial and Submersible Applications.

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 4 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in StreetLight Hand Holes and other Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• UL Tested Ambient Temperature Rating Down To 0°F
• cULus Listed
• Order Qty of 1 = 1 Piece

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 3 Port - This Submersible Insulated Streetlighting Connector Multi-Port can be Used in StreetLighting and other Direct Burial and Submersible Applications.

Submersible Insulated Streetlighting Connectors Multi-Port features #14 - 2/0 3 Port include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in StreetLight Hand Holes and other Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• UL Tested Ambient Temperature Rating Down To 0°F
• cULus Listed
• Order Qty of 1 = 1 Piece

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 2 Port - This Submersible Insulated Streetlighting Connector Multi-Port can be Used in StreetLighting and other Direct Burial and Submersible Applications.

Submersible Insulated Streetlighting Connectors Multi-Port #14 - 2/0 2 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in StreetLight Hand Holes and other Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• UL Tested Ambient Temperature Rating Down To 0°F
• cULus Listed
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 600 MCM 6 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 600 MCM 6 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 600 MCM 4 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 600 MCM 4 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 600 MCM 3 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 600 MCM 3 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 350 MCM 4 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 350 MCM 4 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors Multi-Port Splice #12 - 350 MCM 3 Port - This Multi-Port Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

Multi-Port Submersible Pedestal Splice Connectors #12 - 350 MCM 3 Port features include:

• Fully submersible, completely waterproof Multi-Port Submersible Pedestal Splice
• Designed for Use in Hand Holes, Below Grade Boxes, Direct Burial and Submersible Applications
• Completely Waterproof  Rubber Overmolded Body Ensures Installer Safety and Connector Integrity
• Range Taking Design Covers a Wide Range of Wire Sizes using a Stepped "ROCKET" Sealing Feature
• AL9CU Dual Rated for Both Copper and Aluminum Cables
• Insulated with High Dialectric Strength Abrasion and Chemical Resistant Rubber
• Molded with Precise Fit and Supplied with Removable Access Plugs over the Set Screws
• Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods
• UL 486D Listed for Direct Burial and Submersible Applications
• Complies with ANSI C119.1 Specifications
• 600 Volts
• Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors In-Line Splice #12 - 350 MCM - This In Line Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

In Line Submersible Pedestal Splice Connectors #12 - 350 MCM features include:

• Designed for use in Direct Burial & Submerible installations such as hand holes, below grade boxes, in the ground or submersed in water
• Range Taking Design Reduces Inventory
• AL9CU Dual Rated for Copper and Aluminum Conductors
• Insulated with High Dielectric Strength Tubber Compound
• Molded for Precise Fit & supplied with removable access plugs over the hex screws
• Eliminates the need for Taping, Heat Shrink, Etc.
• Abrasion and Chemical Resistant, will not support combustion
• UL Listed for Wet or Damp Locations, Direct Burial & Submersible per UL 486D
• Complies with ANSI C119.1 Specifications
• 600 Volts
• cULus Listed
• UL tested Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

Submersible Electrical Pedestal Connectors In-Line Splice #14 - 2/0 - This In Line Splice Submersible Pedestal Connector can be Used in Direct Burial and Submersible Applications.

In Line Submersible Pedestal Splice Connectors #14 - 2/0 features include:

• Designed for use in Direct Burial & Submerible installations such as hand holes, below grade boxes, in the ground or submersed in water
• Range Taking Design Reduces Inventory
• AL9CU Dual Rated for Copper and Aluminum Conductors
• Insulated with High Dielectric Strength Tubber Compound
• Molded for Precise Fit & supplied with removable access plugs over the hex screws
• Eliminates the need for Taping, Heat Shrink, Etc.
• Abrasion and Chemical Resistant, will not support combustion
• UL Listed for Wet or Damp Locations, Direct Burial & Submersible per UL 486D
• Complies with ANSI C119.1 Specifications
• 600 Volts
• cULus Listed
• UL tested Ambient Temperature Rating Down To 0°F
• Order Qty of 1 = 1 Piece

#8 - 4/0 In-Line ShakeNSeal Encapsulation Epoxy Resin Splice Kits - These are Fast Easy and Inexpensive Direct Burial and Submersible Electrical Splice Kits.

#8 - 4/0 In-Line ShakeNSeal Encapsulation Epoxy Resin Splice Kits features include:

• Exothermic Epoxy Resin Encapsulation Technology
• UL Listed for Direct Burial & Submersible Splicing Applications
• Durable Impregnable Epoxy Splice kits are Perfect for Above and Below Ground Splicing and Jacket Repair
• Permanent Watertight Seal Protects against Voltage Leakage, Cable Deterioration, & Cable Failure
• Fast Error Proof Setup - Low Viscosity Resin Compound Penetrates Completely Around Splice
• Fungus Resistant
• Stub/Butt/Branch In-Line and Feedthrough Applications
• Rated for use with 194°F(90°C) Cable
• No Tool or Heat Source Required
• UL 486D CSA 198.2 Listed
• 600 Volt maximum
• *67028 Not UL Listed
• cULus Listed
• Order Qty of 1 = 1 Piece

#18 - #1 Large Capacity Butt/Branch ShakeNSeal Encapsulation Epoxy Resin Splice Kits - These are Fast Easy and Inexpensive Direct Burial and Submersible Electrical Splice Kits.

#18 - #1 Large Capacity Butt/Branch ShakeNSeal Encapsulation Epoxy Resin Splice Kits features include:

• Exothermic Epoxy Resin Encapsulation Technology
• UL Listed for Direct Burial & Submersible Splicing Applications
• Durable Impregnable Epoxy Splice kits are Perfect for Above and Below Ground Splicing and Jacket Repair
• Permanent Watertight Seal Protects against Voltage Leakage, Cable Deterioration, & Cable Failure
• Fast Error Proof Setup - Low Viscosity Resin Compound Penetrates Completely Around Splice
• Fungus Resistant
• Stub/Butt/Branch In-Line and Feedthrough Applications
• Rated for use with 194°F(90°C) Cable
• No Tool or Heat Source Required
• UL 486D CSA 198.2 Listed
• 600 Volt maximum
• cULus Listed
• 600 Volt maximum
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal 4/0 Awg 1/2" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals 4/0 Awg 1/2" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal 4/0 Awg 3/8" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals 4/0 Awg 3/8" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal 3/0 Awg 3/8" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals 3/0 Awg 3/8" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal 2/0 Awg 1/2" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals 2/0 Awg 1/2" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal 2/0 Awg 3/8" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals 2/0 Awg 3/8" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal 1/0 Awg 3/8" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals 1/0 Awg 3/8" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal #2 Awg 1/2" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals #2 Awg 1/2" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal #2 Awg 3/8" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals #2 Awg 3/8" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal #4 Awg 3/8" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals #4 Awg 3/8" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Tubular Terminal #6 Awg 3/8" Stud Size - One Hole Copper Tubular Terminal are an excellent choice for DC Power and Solar Applications .

Copper 1 Hole Tubular Terminals #6 Awg 3/8" Stud Size features include:

• Our One Hole Copper Tubular Terminals are made of High-Conductivity Seamless Tubular Copper
• Uniform bright electro-tin plating resists corrosion, reduces contact resistance and gives you maximum conductivity
• Flared Belled barrel edges for ease of conductor insertion
• UL 486A Listed
• 105°C 600V
• Listed for 35KV when properly installed
• UL and cUL Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Flex Cable Short Barrel Compression Splice 350 MCM - Copper Compression Splices for Flex Cable electrical cable terminations.

Copper Flex Cable Short Barrel Compression Splice350 MCM features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Our Copper Flex Cable Splices are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Splices are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Flex Cable Short Barrel Compression Splice 300 MCM - Copper Compression Splices for Flex Cable electrical cable terminations.

Copper Flex Cable Short Barrel Compression Splice 300 MCM features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Our Copper Flex Cable Splices are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Splices are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Flex Cable Short Barrel Compression Splice 250 MCM - Copper Compression Splices for Flex Cable electrical cable terminations.

Copper Flex Cable Short Barrel Compression Splice 250 MCM features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Our Copper Flex Cable Splices are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Splices are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Flex Cable Short Barrel Compression Splice 4/0 Awg - Copper Compression Splices for Flex Cable electrical cable terminations.

Copper Flex Cable Short Barrel Compression Splice 4/0 Awg features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Our Copper Flex Cable Splices are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Splices are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Flex Cable Short Barrel Compression Splice 2/0 Awg - Copper Compression Splices for Flex Cable electrical cable terminations.

Copper Flex Cable Short Barrel Compression Splice 2/0 Awg features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Our Copper Flex Cable Splices are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Splices are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Flex Cable Short Barrel Compression Splice 1/0 Awg - Copper Compression Splices for Flex Cable electrical cable terminations.

Copper Flex Cable Short Barrel Compression Splice 1/0 Awg features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Our Copper Flex Cable Splices are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Splices are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece

Copper Flex Cable Short Barrel Compression Splice #2 Awg - Copper Compression Splices for Flex Cable electrical cable terminations.

Copper Flex Cable Short Barrel Compression Splice #2 Awg features include:

• Flared Belled Entry for Easy Insertion of Fine Strand Flexible Cables such as Class G, Class H, Class I, Class K (Battery), Class M (Welding) and DLO Cable Constructions
• Our Copper Flex Cable Splices are made of high-conductivity Seamless Electrolytic Copper
• Uniform Bright Electro-Tin Plating resists corrosion, reduces contact resistance and maximizes conductivity
• Crimp Marks indicate Proper Crimp Locations
• Compression Splices are Marked with Die Index and Color Codes for easy identification
• UL 486A Listed
• Listed for 35KV when properly installed
• cULus Listed
• Dimension Measurements = Inches
• Order Qty of 1 = 1 Piece