Enable-IT 2-Port Standalone Gigabit PoE 828 Unit - requires your PoE
SKU#: 828
UPC#:896741002096Same Day Shipping likely on orders placed in the next 00 hours 00 minutes 00 seconds.
California Prop 65 Warning
For CA Residents Only.
California Proposition 65 Warning
Proposition 65, officially the Safe Drinking Water and Toxic Enforcement Act of 1986, is a law that requires warnings be provided to California consumers when they might be exposed to chemicals identified by California as causing cancer or reproductive toxicity. The warnings are intended to help California consumers make informed decisions about their exposures to these chemicals from the products they use. The California Office of Environmental Health Hazard Assessment (OEHHA) administers the Proposition 65 program and publishes the listed chemicals, which includes more that 850 chemicals. In August 2016, OEHHA adopted new regulations, effective on August 30, 2018, which change the information required in Proposition 65 warnings.
• WARNING: Some cable, plastic, and metal products may contain chemicals known to the state of CA to cause cancer, birth defects, or other reproductive harm.
For further information, please visit www.P65Warnings.ca.gov
- Description+
- Features+
- Extends standard Gigabit Ethernet Full Duplex 6 times beyond the IEEE barrier of 328ft (100m) with PoE 56V over CAT5e/6 or better wiring.
- Three LAN port design allows for deployment of (2) separate PoE IP Cameras or devices up to 1,200ft (360m).
- DIP switch selection enables you to turn on or off the PoE output for each port.
- Rapid LAN style installation RJ-45 LAN Interfaces – no programming required.
- Cisco / Motorola reverse polarity PoE compatible.
- Daisy chain up to (3) 828’s to 1,200ft (360m).
- Ideal for deploying High Definition IP Cameras requiring Gigabit throughput at distance. Supports VoIP (Voice over IP).
- LAN Device independence – Transparent to 802.3 Protocols, Applications, and MAC / IP addresses.
- Sustained full-duplex service delivery end to end.
- You must supply the PoE to power the 828 standalone unit or you can order the 828P Gigabit PoE Extender.
- Specs+
- 5V DC Self Powered from your PoE Input
- Built in Power Detection triggers full power from your PoE input to pass down the line
- straight through to end devices
- 1000Mbps full-duplex Ethernet Data & PoE (802.3af) or PoE (802.3at)
- Ethernet: (3) LAN RJ-45 Standard 10/100/1000BaseTX, MDI-X, Auto-negotiate ports)
- Thick 1″ (25mm) Width 3.25″ (83mm) Length 4.5″ (114mm)
- Operational Temperature: -49°F to 168°F (-45°to 76°C)
- Humidity: 5% to 95%, non-condensing
- Ruggedized metal wallmount casing with Triple Gigabit LAN Network ports
- Package Contents+
- (1) EnableIT 828 Gigabit & PoE Ethernet Extender Unit
- (1) Enable-IT 828 Quickstart Guide
- (1) 10′ Black Ethernet patch cords
- Reviews+
- Extends standard Gigabit Ethernet Full Duplex 6 times beyond the IEEE barrier of 328ft (100m) with PoE 56V over CAT5e/6 or better wiring.
- Three LAN port design allows for deployment of (2) separate PoE IP Cameras or devices up to 1,200ft (360m).
- DIP switch selection enables you to turn on or off the PoE output for each port.
- Rapid LAN style installation RJ-45 LAN Interfaces – no programming required.
- Cisco / Motorola reverse polarity PoE compatible.
- Daisy chain up to (3) 828’s to 1,200ft (360m).
- Ideal for deploying High Definition IP Cameras requiring Gigabit throughput at distance. Supports VoIP (Voice over IP).
- LAN Device independence – Transparent to 802.3 Protocols, Applications, and MAC / IP addresses.
- Sustained full-duplex service delivery end to end.
- You must supply the PoE to power the 828 standalone unit or you can order the 828P Gigabit PoE Extender.
- 5V DC Self Powered from your PoE Input
- Built in Power Detection triggers full power from your PoE input to pass down the line
- straight through to end devices
- 1000Mbps full-duplex Ethernet Data & PoE (802.3af) or PoE (802.3at)
- Ethernet: (3) LAN RJ-45 Standard 10/100/1000BaseTX, MDI-X, Auto-negotiate ports)
- Thick 1″ (25mm) Width 3.25″ (83mm) Length 4.5″ (114mm)
- Operational Temperature: -49°F to 168°F (-45°to 76°C)
- Humidity: 5% to 95%, non-condensing
- Ruggedized metal wallmount casing with Triple Gigabit LAN Network ports
- (1) EnableIT 828 Gigabit & PoE Ethernet Extender Unit
- (1) Enable-IT 828 Quickstart Guide
- (1) 10′ Black Ethernet patch cords
Enable-IT 2-Port Standalone Gigabit PoE Extender
The Enable-IT™ 828 Gigabit PoE Extender Unit is the world’s 1st and only for 4 years running copper Gigabit PoE Extender Kit solution in the industry today.
This 828 product is a standalone unit to be used with your PoE Injector or PoE Midspan. The standalone 828 can drive incremental Gigabit Ethernet to 800ft (240m). For installing PoE IP cameras, PoE Access Points and remote LAN segments – Nothing is more cost effective or simple to install. The three LAN port design allows for a laptop to be connected and quickly configure devices.
The Enable-IT 828 can drive industry standard Gigabit Ethernet signals to over six times the restricted IEEE standard Ethernet distance when combined in a series of multiple units and uses high power PoE . This cost-effective solution eliminates many of the limitations and high costs for extending LAN cabling today.
The 828 Series Solution is a standalone powered Gigabit Ethernet Repeater that doubles the range of your Gigabit Ethernet to an unpowered remote location.
This is ideal for installing high powered PoE cameras remotely using only a CAT5e or CAT6 rated 100m cabling. Selectable DIP switches allow for disabling PoE output on either output port to enable standard non PoE LAN devices such as a laptop to configure an IP camera.
You can also daisy chain (3) 828 PoE Extender Kit to reach 2,000ft (600m) to power a 56V 50W PoE device easily.
Power
Data Rate
Interface
Dimensions
Environment
Enclosure
Enable-IT 2-Port Standalone Gigabit PoE Extender
The Enable-IT™ 828 Gigabit PoE Extender Unit is the world’s 1st and only for 4 years running copper Gigabit PoE Extender Kit solution in the industry today.
This 828 product is a standalone unit to be used with your PoE Injector or PoE Midspan. The standalone 828 can drive incremental Gigabit Ethernet to 800ft (240m). For installing PoE IP cameras, PoE Access Points and remote LAN segments – Nothing is more cost effective or simple to install. The three LAN port design allows for a laptop to be connected and quickly configure devices.
The Enable-IT 828 can drive industry standard Gigabit Ethernet signals to over six times the restricted IEEE standard Ethernet distance when combined in a series of multiple units and uses high power PoE . This cost-effective solution eliminates many of the limitations and high costs for extending LAN cabling today.
The 828 Series Solution is a standalone powered Gigabit Ethernet Repeater that doubles the range of your Gigabit Ethernet to an unpowered remote location.
This is ideal for installing high powered PoE cameras remotely using only a CAT5e or CAT6 rated 100m cabling. Selectable DIP switches allow for disabling PoE output on either output port to enable standard non PoE LAN devices such as a laptop to configure an IP camera.
You can also daisy chain (3) 828 PoE Extender Kit to reach 2,000ft (600m) to power a 56V 50W PoE device easily.
Power
Data Rate
Interface
Dimensions
Environment
Enclosure